Inconsistent M10

IADInocencio · September 28, 2021, 05:05

I am recently trying to get into CFD again and followed the instructions (correctly I hope) to compile and run DiveMesh and Reef3D on my laptop; I didn't see any errors during the compilation.

Anyway, to test the executables I tried running the 8_6 Rectangular Wave Tank files in the Tutorial; DiveMesh works well creating the necessary files but when I try and run Reef3D is gives me the following error:

read ctrl
!!! Inconsistent M10 parameter, needs to be the same in REEF3D and DIVEMESH !
!!! please check the manual!

My laptop has 6 cores, I am sure I compiled both DiveMesh and Reef3d using "make -j 6". I also edited both ctrl.txt and control.txt to have
M 10 6

Any ideas why it's not running? I didn't have this problem before when I tried on an older laptop.

IADInocencio · September 28, 2021, 06:27

Apologies, but upon checking the other posts in the forum I found the answer at Installation error

It seems typing out the entire "mpirun -n 6 reef3d" worked rather than just typing "reef3d" in the command line allows it to work.

Cheers and apologies again!

kamath · September 28, 2021, 08:13

I am glad that you found your answer on the forum

September 28, 2021, 05:05	Inconsistent M10	#1
IADInocencio Member Ismael Incoencio Join Date: Sep 2021 Posts: 45 Rep Power: 7	I am recently trying to get into CFD again and followed the instructions (correctly I hope) to compile and run DiveMesh and Reef3D on my laptop; I didn't see any errors during the compilation. Anyway, to test the executables I tried running the 8_6 Rectangular Wave Tank files in the Tutorial; DiveMesh works well creating the necessary files but when I try and run Reef3D is gives me the following error: read ctrl !!! Inconsistent M10 parameter, needs to be the same in REEF3D and DIVEMESH ! !!! please check the manual! My laptop has 6 cores, I am sure I compiled both DiveMesh and Reef3d using "make -j 6". I also edited both ctrl.txt and control.txt to have M 10 6 Any ideas why it's not running? I didn't have this problem before when I tried on an older laptop.

September 28, 2021, 06:27		#2
IADInocencio Member Ismael Incoencio Join Date: Sep 2021 Posts: 45 Rep Power: 7	Apologies, but upon checking the other posts in the forum I found the answer at Installation error It seems typing out the entire "mpirun -n 6 reef3d" worked rather than just typing "reef3d" in the command line allows it to work. Cheers and apologies again! kamath likes this.

September 28, 2021, 08:13		#3
kamath Senior Member Arun Kamath Join Date: Nov 2014 Location: Trondheim, Norway Posts: 265 Rep Power: 14	I am glad that you found your answer on the forum __________________ Arun X years with REEF3D

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
My results become inconsistent when using PIMPLE (nOuterCorrectors>1) instead of PISO	FloB	OpenFOAM Running, Solving & CFD	5	May 17, 2021 07:17
[blockMesh] Inconsistent point locations between block pair 7 and 8	ordinary	OpenFOAM Meshing & Mesh Conversion	1	November 27, 2016 12:07
Caradonna&Tung rotor: inconsistent results	Nakki	FLUENT	14	December 8, 2015 12:11
[blockMesh] Error while creating blockMesh: Inconsistent point locations between block pair	lpashwin	OpenFOAM Meshing & Mesh Conversion	2	June 1, 2015 13:31
redistributeMeshPar with scotch fails	matteoL	OpenFOAM Pre-Processing	0	March 30, 2015 12:13