Unable to view inside the cylinder

valr · June 27, 2017, 10:03

Hi everyone,

I am working on CFD simulation of water in rotating drum. BlockMesh and simulation runs well.

But when I am trying to view it in ParaView, I could not see the water inside the drum. I also tried using "clip" , "slice" and "contour" commands. But it did not work. I could not also rotate the drum in paraview.

The following is the link to the cases of my project:
https://drive.google.com/drive/folde...kU?usp=sharing

I am using Dam Break tutorial and changed it according to needs.
Can anyone help me overcome this problem?��

saddy · July 6, 2017, 12:42

HEY FIRST OF ALL UR LINK IS EMPTY
second. did you see the water at the initial time=0 after running setfields. u should always check whether water has been set in domain initially or not
so check at t=0, if u see water then, there should be no problem in visualizing it at a later time

valr · July 6, 2017, 22:52

Hi,

Sorry, I changed the link. Now I think it works. I checked initially also water wasn't there.

https://drive.google.com/drive/folde...kU?usp=sharing

Thanks saddy for your reply.

wyldckat · August 27, 2017, 15:51

Quick answer: I've come here due to a PM you sent me and only today did I finally manage to look into this.

Take a look into the sloshing tank tutorial cases. The following thread has a lot of details about it: what is the difference between sloshingTank3D and sloshingTank3D3DoF?

June 27, 2017, 10:03	Unable to view inside the cylinder	#1
valr New Member Join Date: Jun 2017 Posts: 9 Rep Power: 9	Hi everyone, I am working on CFD simulation of water in rotating drum. BlockMesh and simulation runs well. But when I am trying to view it in ParaView, I could not see the water inside the drum. I also tried using "clip" , "slice" and "contour" commands. But it did not work. I could not also rotate the drum in paraview. The following is the link to the cases of my project: https://drive.google.com/drive/folde...kU?usp=sharing I am using Dam Break tutorial and changed it according to needs. Can anyone help me overcome this problem?�� blitzkg likes this. Last edited by valr; July 6, 2017 at 22:48.

July 6, 2017, 12:42		#2
saddy Senior Member sandy Join Date: Feb 2016 Location: . Posts: 117 Rep Power: 10	HEY FIRST OF ALL UR LINK IS EMPTY second. did you see the water at the initial time=0 after running setfields. u should always check whether water has been set in domain initially or not so check at t=0, if u see water then, there should be no problem in visualizing it at a later time valr likes this.

August 27, 2017, 15:51		#4
wyldckat Retired Super Moderator Bruno Santos Join Date: Mar 2009 Location: Lisbon, Portugal Posts: 10,981 Blog Entries: 45 Rep Power: 128	Quick answer: I've come here due to a PM you sent me and only today did I finally manage to look into this. Take a look into the sloshing tank tutorial cases. The following thread has a lot of details about it: what is the difference between sloshingTank3D and sloshingTank3D3DoF? __________________ OpenFOAM: FAQ \| Getting started Forum: How to get help, to post code/output and forum guide Read this before sending me PM

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Viewing a constant/variable inside para view	sur4j	OpenFOAM Programming & Development	6	December 24, 2013 01:55
trying to simulate the compression stroke inside cylinder, using UDF for injection	mayur	Fluent UDF and Scheme Programming	15	December 16, 2013 05:30
Unable to restart the Field View after it crashes	bikash	FieldView	0	May 8, 2013 06:52
natural convection inside a cylinder	afnene	FLUENT	2	December 10, 2010 12:04
[Commercial meshers] ST_Malloc: out of memory.malloc_storage: unable to malloc Velocity SA,	cfdproject	OpenFOAM Meshing & Mesh Conversion	0	April 14, 2009 16:45

July 6, 2017, 22:52		#3
valr New Member Join Date: Jun 2017 Posts: 9 Rep Power: 9	Hi, Sorry, I changed the link. Now I think it works. I checked initially also water wasn't there. https://drive.google.com/drive/folde...kU?usp=sharing Thanks saddy for your reply.