[Commercial meshers] mesh conversion from ansys mesher to openfoam

Dusan1224 · November 4, 2015, 06:08

hi, i made tetrahedral mesh include influence layer in ansys meshing and tried to convert into openfoam, but this message appeared. its not my first mesh conversion from ansys, some of them converted good, so i need to know, if is the geometry of mesh wrong ,or whare could be posibly problem?
ps. i used comands fluentMeshToFoam, and also tried ansysToFoam, and both times it wrote me same error:

--> FOAM FATAL IO ERROR:
wrong token type - expected word, found on line 25 the label 800

file: /home/supermicro/Dusan_K/cfd/openfoam/ref_zak_podlaha_2D_C/system/controlDict.startFrom at line 25.

From function operator>>(Istream&, word&)
in file primitives/strings/word/wordIO.C at line 74.

FOAM exiting

akidess · November 4, 2015, 06:21

Did you read the message? You have something weird in your controlDict for the entry startFrom. At the very least you should have uploaded your controlDict here.

Dusan1224 · November 5, 2015, 04:41

Thx a lot. I used this "template" many times without problem, so i didnt even think there could be error. i checked the document, and starting time was changed from "latestTime" to "800" ( from previos simulation) . but i didnt think this could cause to error while import mesh

November 4, 2015, 06:08	mesh conversion from ansys mesher to openfoam	#1
Dusan1224 New Member Dusan Konkoly Join Date: Nov 2015 Posts: 2 Rep Power: 0	hi, i made tetrahedral mesh include influence layer in ansys meshing and tried to convert into openfoam, but this message appeared. its not my first mesh conversion from ansys, some of them converted good, so i need to know, if is the geometry of mesh wrong ,or whare could be posibly problem? ps. i used comands fluentMeshToFoam, and also tried ansysToFoam, and both times it wrote me same error: --> FOAM FATAL IO ERROR: wrong token type - expected word, found on line 25 the label 800 file: /home/supermicro/Dusan_K/cfd/openfoam/ref_zak_podlaha_2D_C/system/controlDict.startFrom at line 25. From function operator>>(Istream&, word&) in file primitives/strings/word/wordIO.C at line 74. FOAM exiting

November 4, 2015, 06:21		#2
akidess Senior Member Anton Kidess Join Date: May 2009 Location: Germany Posts: 1,377 Rep Power: 30	Did you read the message? You have something weird in your controlDict for the entry startFrom. At the very least you should have uploaded your controlDict here. Dusan1224 likes this. __________________ On twitter @akidTwit Spend as much time formulating your questions as you expect people to spend on their answer.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[Other] [Request] OpenFOAM mesh to 2D Ansys fluent mesh	anon_q	OpenFOAM Community Contributions	6	July 3, 2023 06:24
[Commercial meshers] Mesh conversion .gtm to OpenFOAM	ansab	OpenFOAM Meshing & Mesh Conversion	2	December 6, 2016 14:48
[ANSYS Meshing] Assigning different mesh densities for different parts in ANSYS ICEMCFD Tetra Mesher	johnnydrama7	ANSYS Meshing & Geometry	0	September 19, 2016 14:10
Moving mesh	Niklas Wikstrom (Wikstrom)	OpenFOAM Running, Solving & CFD	122	June 15, 2014 07:20
fluent add additional zones for the mesh file	SSL	FLUENT	2	January 26, 2008 12:55

November 5, 2015, 04:41		#3
Dusan1224 New Member Dusan Konkoly Join Date: Nov 2015 Posts: 2 Rep Power: 0	Thx a lot. I used this "template" many times without problem, so i didnt even think there could be error. i checked the document, and starting time was changed from "latestTime" to "800" ( from previos simulation) . but i didnt think this could cause to error while import mesh