[openSmoke] flameletSmoke + new ODESolver (by Alberto Cuoci)

Tobi · September 18, 2017, 11:39

Hi all, I just want to open a new thread about the flameletModel which was published by the CRECK modelling group (Milano). The library was first named libOpenSMOKE. I was using it during my masterthesis. A long and intensive discussion about that library can be checkout out here: https://www.cfd-online.com/Forums/op...opensmoke.html (note: 27 pages). During my thesis I was modifying it and kept it up to date with the latest OpenFOAM releases which can be found here: https://bitbucket.org/shor-ty/flameletmodel/

The official libOpenSMOKE is not distributed by the CRECK modelling group anymore but Bruno Santos has the old version (for OpenFOAM 1.7.x) available. You can find it here: https://github.com/wyldckat/libOpenSMOKE

However, both versions libOpenSMOKE and the flameletModel (Holzmann-cfd - extension of libOpenSMOKE) are not updated anymore based on the fact that the CRECK modeling group has published new flamelet solvers and libraries. Right now, I did not check the abilities of these libraries but they should offer more (e.g. including bug fixes and extensions) than the libOpenSMOKE and the extended and updated flameletModel that I host. You find the libraries and solvers here:

https://github.com/acuoci

laminarSmoke
flameletSmoke
openSmoke
ODESmoke

Have fun

ecbmxer · November 21, 2017, 19:24

I've been interested in trying the laminarSMOKE library for doing some laminar oxy-fuel diffusion flame modeling. But so far I've not had any success in compiling the solvers (the user-defined BC and radiation libraries compiled fine).

I believe I have satisfied the compulsory library requirements (at least for the minimal install), but am running into a lot of "no such file or directory" errors.

This is for OF 2.3.0. Wonder if anyone else has had similar experience? Or perhaps I'm just missing something...

September 18, 2017, 11:39	flameletSmoke + new ODESolver (by Alberto Cuoci)	#1
Tobi Super Moderator Tobias Holzmann Join Date: Oct 2010 Location: Bad Wörishofen Posts: 2,711 Blog Entries: 6 Rep Power: 52	Hi all, I just want to open a new thread about the flameletModel which was published by the CRECK modelling group (Milano). The library was first named libOpenSMOKE. I was using it during my masterthesis. A long and intensive discussion about that library can be checkout out here: https://www.cfd-online.com/Forums/op...opensmoke.html (note: 27 pages). During my thesis I was modifying it and kept it up to date with the latest OpenFOAM releases which can be found here: https://bitbucket.org/shor-ty/flameletmodel/ The official libOpenSMOKE is not distributed by the CRECK modelling group anymore but Bruno Santos has the old version (for OpenFOAM 1.7.x) available. You can find it here: https://github.com/wyldckat/libOpenSMOKE However, both versions libOpenSMOKE and the flameletModel (Holzmann-cfd - extension of libOpenSMOKE) are not updated anymore based on the fact that the CRECK modeling group has published new flamelet solvers and libraries. Right now, I did not check the abilities of these libraries but they should offer more (e.g. including bug fixes and extensions) than the libOpenSMOKE and the extended and updated flameletModel that I host. You find the libraries and solvers here: https://github.com/acuoci laminarSmoke flameletSmoke openSmoke ODESmoke Have fun Uyan likes this. __________________ Keep foaming, Tobias Holzmann Last edited by Tobi; October 9, 2017 at 05:26.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
A trial of implementing of CVODE as ODESolver	Aleksey_R	OpenFOAM Programming & Development	12	September 9, 2020 00:32

November 21, 2017, 19:24		#2
ecbmxer Member Clint Bedick Join Date: May 2011 Posts: 43 Rep Power: 15	I've been interested in trying the laminarSMOKE library for doing some laminar oxy-fuel diffusion flame modeling. But so far I've not had any success in compiling the solvers (the user-defined BC and radiation libraries compiled fine). I believe I have satisfied the compulsory library requirements (at least for the minimal install), but am running into a lot of "no such file or directory" errors. This is for OF 2.3.0. Wonder if anyone else has had similar experience? Or perhaps I'm just missing something...