How to create C-grid in GridPro

TedBrogan · September 25, 2014, 21:43

All,

Can anyone please tell me how to go about creating a C-grid around an airfoil in GridPro? My solver is coded for that topology only. I am moving towards a 3D periodic C-grid about a blade, but I can probably figure that out after I see how a C-grid can be forced as the output in GridPro.

Many thanks for any help you can offer.

chitra.s · September 29, 2014, 09:24

Quote:

Originally Posted by TedBrogan

All,

Can anyone please tell me how to go about creating a C-grid around an airfoil in GridPro? My solver is coded for that topology only. I am moving towards a 3D periodic C-grid about a blade, but I can probably figure that out after I see how a C-grid can be forced as the output in GridPro.

Many thanks for any help you can offer.

Dear TedBrogan,

Please check the attached tutorial over here.
https://db.tt/f4xSP9fw

Please revert back if it does not help.

Regards,
Chitra

TedBrogan · September 29, 2014, 15:18

Extremely useful tutorial. I was looking for something like that, but I could not find it anywhere. Thank you so much.

kaszt · January 23, 2018, 18:13

Hi, I'm interested in meshing an airfoil using GridPro as well - the link to the tutorial is no longer active, would it be possible to ask for the tutorial?

vimaero · January 25, 2018, 00:37

Dear Katherine,

You can look at the following tutorial. It was explained with respect to GridPro's old UI(az). May be you can look at the concept and try to execute the same in the new GUI.

https://www.dropbox.com/s/vcfuw4afjk..._edge.pdf?dl=0

Best Regards,
Vimal

kaszt · January 25, 2018, 14:00

Hi Vimal,

Thank you very much for the tutorial! I am brand new to GridPro, so this helps in getting familiar with the software. Thanks again!

Sincerely,
Katherine

September 25, 2014, 21:43	How to create C-grid in GridPro	#1
TedBrogan New Member patty Join Date: Nov 2010 Posts: 21 Rep Power: 16	All, Can anyone please tell me how to go about creating a C-grid around an airfoil in GridPro? My solver is coded for that topology only. I am moving towards a 3D periodic C-grid about a blade, but I can probably figure that out after I see how a C-grid can be forced as the output in GridPro. Many thanks for any help you can offer.

September 29, 2014, 15:18		#3
TedBrogan New Member patty Join Date: Nov 2010 Posts: 21 Rep Power: 16	Extremely useful tutorial. I was looking for something like that, but I could not find it anywhere. Thank you so much. sameben likes this.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Mesh Conversion : structured to unstructured	shreyasr	ANSYS	8	April 8, 2019 08:03
Actuator disk model	audrich	FLUENT	0	September 21, 2009 08:06
Where's the singularity/mesh flaw?	audrich	FLUENT	3	August 4, 2009 02:07
2d irregular grid	Remy	Main CFD Forum	1	December 22, 2008 05:49
Troubles modelling flow through a grid	Hans Klaufus	CFX	1	June 28, 2000 17:43

January 23, 2018, 18:13		#4
kaszt New Member Katherine Join Date: Feb 2016 Posts: 20 Rep Power: 10	Hi, I'm interested in meshing an airfoil using GridPro as well - the link to the tutorial is no longer active, would it be possible to ask for the tutorial?

January 25, 2018, 00:37		#5
vimaero New Member Vimalraj Join Date: Apr 2013 Location: Bangalore Posts: 29 Rep Power: 13	Dear Katherine, You can look at the following tutorial. It was explained with respect to GridPro's old UI(az). May be you can look at the concept and try to execute the same in the new GUI. https://www.dropbox.com/s/vcfuw4afjk..._edge.pdf?dl=0 Best Regards, Vimal

January 25, 2018, 14:00		#6
kaszt New Member Katherine Join Date: Feb 2016 Posts: 20 Rep Power: 10	Hi Vimal, Thank you very much for the tutorial! I am brand new to GridPro, so this helps in getting familiar with the software. Thanks again! Sincerely, Katherine