how to go back to upper in command prompt

July 4, 2005, 04:41

how to go back to upper in command prompt of fluent?

thx in advance!

asal · July 4, 2005, 04:58

ok. it's 'q'.

lukasf · February 19, 2019, 03:50

use quit (ANSYS Fluent R18.2 Academic).

q does not work.

https://www.sharcnet.ca/Software/Flu.../ug/node49.htm

LuckyTran · February 19, 2019, 09:44

Code:

To move back to the previously occupied menu, type  q or  quit at the prompt.

q or quit both works unless your system has a strange parser

Bdew8556 · October 13, 2022, 01:31

Hey guys,

On that note, can anyone remember what the key shortcut is so you dont have to type the whole command? similar to how TAB works on linux.

For example if the text is "write-settings" I believe there is a way where I can just write "write-se" then hit a key and it will finish the line.

AlexanderZ · October 13, 2022, 02:38

there is not "shortcut" key
however, for "write-settings" you may even write "ws" if there are no options which could be called as "ws" (for instance if except "write-settings" there is "write-surface-clusters" "ws" could call both this functions, so you may use "wset" instead)

July 4, 2005, 04:41	how to go back to upper in command prompt	#1
Bingzhi Li Guest Posts: n/a	how to go back to upper in command prompt of fluent? thx in advance!

July 4, 2005, 04:58	Re: how to go back to upper in command prompt	#2
Bingzhi Li Guest Posts: n/a	ok. it's 'q'. asal, Brathmann, Gbeatz and 20 others like this.

February 19, 2019, 03:50		#3
lukasf Senior Member Lukas Fischer Join Date: May 2018 Location: Germany, Munich Posts: 117 Rep Power: 8	use quit (ANSYS Fluent R18.2 Academic). q does not work. https://www.sharcnet.ca/Software/Flu.../ug/node49.htm BrainsReact likes this.

February 19, 2019, 09:44		#4
LuckyTran Senior Member Lucky Join Date: Apr 2011 Location: Orlando, FL USA Posts: 5,764 Rep Power: 66	Code: To move back to the previously occupied menu, type q or quit at the prompt. q or quit both works unless your system has a strange parser mathru and dah_someone like this.

October 13, 2022, 02:38		#6
AlexanderZ Senior Member Alexander Join Date: Apr 2013 Posts: 2,363 Rep Power: 34	there is not "shortcut" key however, for "write-settings" you may even write "ws" if there are no options which could be called as "ws" (for instance if except "write-settings" there is "write-surface-clusters" "ws" could call both this functions, so you may use "wset" instead) __________________ best regards ****************************** press LIKE if this message was helpful

October 13, 2022, 01:31		#5
Bdew8556 Senior Member Brett Join Date: May 2013 Posts: 217 Rep Power: 14	Hey guys, On that note, can anyone remember what the key shortcut is so you dont have to type the whole command? similar to how TAB works on linux. For example if the text is "write-settings" I believe there is a way where I can just write "write-se" then hit a key and it will finish the line.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Pressure outlet and back flow	eric	FLUENT	11	November 6, 2014 12:03
back pressure at exit for supersonic flow	BigFrank	FLUENT	6	April 24, 2014 16:13
exporting from Fluent back into Gambit	tom	FLUENT	0	June 23, 2008 17:55
Transient Run from Back up	selim	CFX	0	March 5, 2008 06:56
Back up from Solver	selim	CFX	1	March 5, 2008 05:52