Deactivating a zone in the middle of simulation

Rashi · April 9, 2021, 13:02

Hi all,

I'm doing a FSI simulation for a melting and soldification process. After the mold solidifies I need to let it cool until it reach room temperature. Therefore, can I deactivate the cast zone in the middle of simulation and continue it wihtout loosing data?
Also is there a way to setup convergence criteria so that simulation stops when the mold reaches the solidus temperature?

Thank you.

Yasser · April 9, 2021, 15:35

The answer to your questions, yes and yes ...

You can change the boundary condition type in the middle of simulation use Execute Commands but this could be done at certain time .. not event. If you provide more details, there might be another way that you can use ..

You can set your convergence criteria .. go to Monitor -- > Residuals -- > convergence criteria and make your own criteria. You might need to use a simple UDF to check your criteria and pass a value of the solver to stop.

Rashi · April 9, 2021, 15:51

Hi Yasser, so we meet again!

Did you had any luck with compute canada?
I will send an reply with more detailed explanation.

Rashi · April 13, 2021, 15:46

Hi Yasser,

Thank you for your reply.

I'm doing a solidification/melting simulation to obtain the temperature/time output to simulate residual stresses in casted object.

In fluent simulation first I want to simulate from pouring temperature until the shakedown temperature with the mold intact and then I want to remove the mold and let it cool till it reach room temerpature.

It seems if I can have a convergence criteria I can fully automate the process right? With some custom TUI commands I mean.

Cheers,
Rashiga

April 9, 2021, 13:02	Deactivating a zone in the middle of simulation	#1
Rashi New Member Rashiga Walallawita Join Date: Mar 2013 Posts: 13 Rep Power: 13	Hi all, I'm doing a FSI simulation for a melting and soldification process. After the mold solidifies I need to let it cool until it reach room temperature. Therefore, can I deactivate the cast zone in the middle of simulation and continue it wihtout loosing data? Also is there a way to setup convergence criteria so that simulation stops when the mold reaches the solidus temperature? Thank you.

April 9, 2021, 15:51		#3
Rashi New Member Rashiga Walallawita Join Date: Mar 2013 Posts: 13 Rep Power: 13	Hi Yasser, so we meet again! Did you had any luck with compute canada? I will send an reply with more detailed explanation. Yasser likes this.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Fluent Parallelization Problem After AC Power Dropped	pawl	Hardware	5	November 13, 2016 07:08
Pressure input for Velocity Inlet in middle of 2D transient Simulation	Shekhaai	FLUENT	1	August 30, 2016 23:43
How to setup simulation of injet Helium into Air cell zone?	Shogan	FLUENT	2	December 10, 2014 07:29
Sudden jumps in Courant in the middle of the simulation	Pj.	OpenFOAM Running, Solving & CFD	1	May 6, 2014 13:23
Porosity profile, dividing a zone, or getting zone location from zone	khoopes	FLUENT	0	June 2, 2012 20:39

April 9, 2021, 15:35		#2
Yasser Member Yasser Selima Join Date: Mar 2009 Location: Canada Posts: 51 Rep Power: 19	The answer to your questions, yes and yes ... You can change the boundary condition type in the middle of simulation use Execute Commands but this could be done at certain time .. not event. If you provide more details, there might be another way that you can use .. You can set your convergence criteria .. go to Monitor -- > Residuals -- > convergence criteria and make your own criteria. You might need to use a simple UDF to check your criteria and pass a value of the solver to stop.

April 13, 2021, 15:46		#4
Rashi New Member Rashiga Walallawita Join Date: Mar 2013 Posts: 13 Rep Power: 13	Hi Yasser, Thank you for your reply. I'm doing a solidification/melting simulation to obtain the temperature/time output to simulate residual stresses in casted object. In fluent simulation first I want to simulate from pouring temperature until the shakedown temperature with the mold intact and then I want to remove the mold and let it cool till it reach room temerpature. It seems if I can have a convergence criteria I can fully automate the process right? With some custom TUI commands I mean. Cheers, Rashiga