the unexpected issue!

hamidciv · January 9, 2018, 11:01

Hello everyone!

i'm using Flow3D V11.2. I've encountered so weird issue as I've run the model on two different computers under the same settings, but the results showed a difference rates of the scour depth & ridge in the two cases!!!

I've got confused, and I really don't know what to do. have you ever faced this issue so far?

I would be grateful if someone could guide me on this.

best regards
hamid

hamidciv · January 10, 2018, 13:17

Can anyone tell me whats happening? I would really appreciate any feedback you can give me.

thunde47 · January 11, 2018, 18:39

Please share the configurations of the two computers and the input files.

hamidciv · January 12, 2018, 04:31

Hi Dear Adwaith, thanks for your attention!

Please find attached the requested configurations of the two different computers. unfortunately, i dont understand what you mean by "input fies", did you mean the prepin files? if so, i've compared many times the two different prepin files line by line, and there was no difference between them.

best regards
hamid

thunde47 · January 12, 2018, 12:56

Also attach the prepin file.

hamidciv · January 13, 2018, 10:58

Dear Adwaith;

i'm sorry to say that i can't disclose my file in here because that's work in progress and thus confidencial.

thanks

January 9, 2018, 11:01	the unexpected issue!	#1
hamidciv Senior Member Hydreaulic structures Join Date: Sep 2012 Posts: 283 Rep Power: 15	Hello everyone! i'm using Flow3D V11.2. I've encountered so weird issue as I've run the model on two different computers under the same settings, but the results showed a difference rates of the scour depth & ridge in the two cases!!! I've got confused, and I really don't know what to do. have you ever faced this issue so far? I would be grateful if someone could guide me on this. best regards hamid

January 11, 2018, 18:39		#3
thunde47 Senior Member thunde47 Join Date: Dec 2015 Location: India, USA Posts: 133 Blog Entries: 1 Rep Power: 11	Please share the configurations of the two computers and the input files. hamidciv likes this.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
ANSYS Workbench on "Uncertified" Linux Distros	hsr	CFX	289	April 20, 2023 10:23
[OpenFOAM.org] Issue with bashrc file encountering unexpected EOF	TexasTechsan	OpenFOAM Installation	1	June 25, 2017 14:07
FLUENT installation on UBUNTU 12.04 (LTS)	teymourj	FLUENT	2	March 1, 2017 23:24
error 262144 and unexpected disconnect when run on 2 nodes	Emily1412	SU2 Installation	1	April 10, 2014 18:08
Meshing related issue in Flow EFD	appu	FloEFD, FloWorks & FloTHERM	1	May 22, 2011 09:27

January 10, 2018, 13:17		#2
hamidciv Senior Member Hydreaulic structures Join Date: Sep 2012 Posts: 283 Rep Power: 15	Can anyone tell me whats happening? I would really appreciate any feedback you can give me.

January 12, 2018, 12:56		#5
thunde47 Senior Member thunde47 Join Date: Dec 2015 Location: India, USA Posts: 133 Blog Entries: 1 Rep Power: 11	Also attach the prepin file.

January 13, 2018, 10:58		#6
hamidciv Senior Member Hydreaulic structures Join Date: Sep 2012 Posts: 283 Rep Power: 15	Dear Adwaith; i'm sorry to say that i can't disclose my file in here because that's work in progress and thus confidencial. thanks