variable heat flux as boundary conditions at a trapezoidal receiver in a CSP plant

Louiza RBH · September 27, 2016, 08:22

Hello everybody,
I'm PhD student and i'm looking for temperature distribution on my trapezoidal receiver for Linear Fresnel Mirrors.
Using Tonatiuh and Mathematica, i obtained heat flux distribution (W/m2) and now i'm using Comsol to find temperature distribution.
The heat flux is not constant so i'm asking you how can i use my variable heat flux in boundary conditions.
I thank you in advance for attention you will give to my message.
In conclusion, i have variable heat flux boundary conditions.

meusha · September 29, 2016, 08:32

The heat flux should be expressed as a function of location i.e.

h=f(x,y,z)

You should then enter this function as the boundary condition under the right domain, instead of using a fixed value. You must know the ANSYS CFX syntax to be able to translate the actual function in to something that is understandable by ANSYS.

Louiza RBH · September 29, 2016, 08:43

Thank you meusha for your help.
I think it's exactly what i have to do. I'm looking for this function but considering the angle (teta), because my heat flux varies as a function of it.
I'll define angle= f(x,y) in the variables icon so the software can recognize teta.
Thank you again for your response and for the importance that you gave to my message

September 27, 2016, 08:22	variable heat flux as boundary conditions at a trapezoidal receiver in a CSP plant	#1
Louiza RBH New Member Louiza RABHI Join Date: Sep 2016 Posts: 2 Rep Power: 0	Hello everybody, I'm PhD student and i'm looking for temperature distribution on my trapezoidal receiver for Linear Fresnel Mirrors. Using Tonatiuh and Mathematica, i obtained heat flux distribution (W/m2) and now i'm using Comsol to find temperature distribution. The heat flux is not constant so i'm asking you how can i use my variable heat flux in boundary conditions. I thank you in advance for attention you will give to my message. In conclusion, i have variable heat flux boundary conditions.

September 29, 2016, 08:32		#2
meusha New Member No Real Name Join Date: Sep 2016 Posts: 4 Rep Power: 10	The heat flux should be expressed as a function of location i.e. h=f(x,y,z) You should then enter this function as the boundary condition under the right domain, instead of using a fixed value. You must know the ANSYS CFX syntax to be able to translate the actual function in to something that is understandable by ANSYS. Louiza RBH likes this.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Wind turbine simulation	Saturn	CFX	60	July 17, 2024 06:45
How to solve the heat source (by heat flux or Heat load Boundary conditions)	ernarasimman	OpenFOAM Running, Solving & CFD	0	October 29, 2015 08:19
[swak4Foam] Heat Flux boundary conditions with groovyBC for chtMultiRegionFoam with solids only	Kumudu	OpenFOAM Community Contributions	7	August 23, 2014 15:33
mixed boundary conditions including heat flux, convective heat transfer and radiation	lotus_blue	FLUENT	0	April 3, 2013 19:55
CFX doesn't continue calculation...	mactech001	CFX	6	November 15, 2009 22:25

September 29, 2016, 08:43		#3
Louiza RBH New Member Louiza RABHI Join Date: Sep 2016 Posts: 2 Rep Power: 0	Thank you meusha for your help. I think it's exactly what i have to do. I'm looking for this function but considering the angle (teta), because my heat flux varies as a function of it. I'll define angle= f(x,y) in the variables icon so the software can recognize teta. Thank you again for your response and for the importance that you gave to my message