Initialize Profile Data Variables

aero_head · April 24, 2021, 21:56

Hello Everyone,

Just wanted to confirm something;

I have to initialize velocity profile data as the initial condition for my simulation.

I just wanted to know which coordinates the velocity components belong to i.e. velocity u = X direction, velocity v = Y direction, velocity w = Z direction or streamwise= vel u, wall normal= vel v, spanwise= vel w. I looked in the documentation CFX-Solver Modelling Guide, p.102 of Release 16.0, which seems to suggest it is the former case i.e. velocity u = X direction, etc.

In my case, I have Z as my streamwise directional coordinate, so I ran it with my velocity values as vel w and the initial results seem reasonable, but I have trust issues with myself and wanted to see what the verdict was on here.

ghorrocks · April 24, 2021, 22:49

Velocity u = X, Velocity v = Y, Velocity w = Z is correct.

aero_head · April 24, 2021, 23:36

Thank you so much for your reply, Glenn! That clears it up for me, much appreciated!

aero_head · April 25, 2021, 16:17

Oh, one other thing I just thought of; Say my inlet is at 0 and my outlet is at -1. Would it make sense for the velocity w values to get initialized with negative values?

ghorrocks · April 25, 2021, 19:14

Yes, that is fine.

aero_head · April 25, 2021, 20:07

Thank you so much again, Glenn!

April 24, 2021, 21:56	Initialize Profile Data Variables	#1
aero_head Senior Member Kira Join Date: Nov 2020 Location: Canada Posts: 435 Rep Power: 9	Hello Everyone, Just wanted to confirm something; I have to initialize velocity profile data as the initial condition for my simulation. I just wanted to know which coordinates the velocity components belong to i.e. velocity u = X direction, velocity v = Y direction, velocity w = Z direction or streamwise= vel u, wall normal= vel v, spanwise= vel w. I looked in the documentation CFX-Solver Modelling Guide, p.102 of Release 16.0, which seems to suggest it is the former case i.e. velocity u = X direction, etc. In my case, I have Z as my streamwise directional coordinate, so I ran it with my velocity values as vel w and the initial results seem reasonable, but I have trust issues with myself and wanted to see what the verdict was on here.

April 24, 2021, 22:49		#2
ghorrocks Super Moderator Glenn Horrocks Join Date: Mar 2009 Location: Sydney, Australia Posts: 17,870 Rep Power: 144	Velocity u = X, Velocity v = Y, Velocity w = Z is correct. aero_head likes this. __________________ Note: I do not answer CFD questions by PM. CFD questions should be posted on the forum.

April 25, 2021, 19:14		#5
ghorrocks Super Moderator Glenn Horrocks Join Date: Mar 2009 Location: Sydney, Australia Posts: 17,870 Rep Power: 144	Yes, that is fine. aero_head likes this. __________________ Note: I do not answer CFD questions by PM. CFD questions should be posted on the forum.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Unsteady Boundary Profile with data file	Arianna	FLUENT	34	July 29, 2019 17:35
[ICEM] profile data	svaezi	ANSYS Meshing & Geometry	0	September 18, 2016 04:13
Transient profile data	bongbang	CFX	2	February 14, 2015 16:03
Fail to generate transient profile data ?	dotapro	CFX	0	February 6, 2015 04:06
[General] 2 datas on one plot	Akuji	ParaView	46	December 1, 2013 15:06

April 24, 2021, 23:36		#3
aero_head Senior Member Kira Join Date: Nov 2020 Location: Canada Posts: 435 Rep Power: 9	Thank you so much for your reply, Glenn! That clears it up for me, much appreciated!

April 25, 2021, 16:17		#4
aero_head Senior Member Kira Join Date: Nov 2020 Location: Canada Posts: 435 Rep Power: 9	Oh, one other thing I just thought of; Say my inlet is at 0 and my outlet is at -1. Would it make sense for the velocity w values to get initialized with negative values?

April 25, 2021, 20:07		#6
aero_head Senior Member Kira Join Date: Nov 2020 Location: Canada Posts: 435 Rep Power: 9	Thank you so much again, Glenn!