it doesn't have "topology estimate factor zif"

eng_norouzi · October 2, 2012, 05:12

Hi
cfx 12.1 gives this error for my simulation:

ERROR #001100279 has occurred in subroutine ErrAction.
Message:
SYMASS_ZIFCS_EL: The solver ran out of temporary space while building a linked list for a domain interface. Try setting the expert parameter "topology estimate factor zif" to a value greater than 1.0. Values higher than 1.2 should not be necessary.

but in expert parameter it doesnt have "topology estimate factor zif" option!! it just has "topology estimate factor" what should I do with this error?
I found this option in cfx 13 but not in cfx 12.1

thanks

energy382 · October 2, 2012, 11:22

normally, you should find it here:

=> simulation/flow analysis/solver/insert/expert...

it would surprise me, if v.12 doesn't have this paramter

eng_norouzi · October 3, 2012, 03:29

I'm surprised too!
I searched it in expert parameter---->convergence
it has "topology estimate factor" but not "topology estimate factor zif"
I'm really confused I've checked it 10 times!!
I couldn't find it even in cfx 12.1 help.
I know that this option is on cfx 13.can anybody check it on cfx 12.1 please?

thanks

eng_norouzi · October 4, 2012, 10:35

I know what is this error for I just can't find the option
can anybody help me to find it please?
maybe my cfx doesn't have it
can you check it please

singer1812 · October 4, 2012, 18:21

Go in the command editor foor Expert Parameters and just type it in as the instructions say. CFX will accept it.

welaa · January 23, 2013, 16:10

hi
I have the error massage same to above. I used ANSYS v13 want to change topology estimate factor zif . Or how to eliminate this massage

October 2, 2012, 05:12	it doesn't have "topology estimate factor zif"	#1
eng_norouzi Member ali Join Date: Feb 2011 Posts: 37 Rep Power: 15	Hi cfx 12.1 gives this error for my simulation: ERROR #001100279 has occurred in subroutine ErrAction. Message: SYMASS_ZIFCS_EL: The solver ran out of temporary space while building a linked list for a domain interface. Try setting the expert parameter "topology estimate factor zif" to a value greater than 1.0. Values higher than 1.2 should not be necessary. but in expert parameter it doesnt have "topology estimate factor zif" option!! it just has "topology estimate factor" what should I do with this error? I found this option in cfx 13 but not in cfx 12.1 thanks welaa likes this.

October 2, 2012, 11:22		#2
energy382 Senior Member Christoph Join Date: May 2011 Location: Germany Posts: 182 Rep Power: 18	normally, you should find it here: => simulation/flow analysis/solver/insert/expert... it would surprise me, if v.12 doesn't have this paramter amin_gls and Hyungyu Lee like this.

October 3, 2012, 03:29		#3
eng_norouzi Member ali Join Date: Feb 2011 Posts: 37 Rep Power: 15	I'm surprised too! I searched it in expert parameter---->convergence it has "topology estimate factor" but not "topology estimate factor zif" I'm really confused I've checked it 10 times!! I couldn't find it even in cfx 12.1 help. I know that this option is on cfx 13.can anybody check it on cfx 12.1 please? thanks Last edited by eng_norouzi; October 4, 2012 at 04:18.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
How to estimate roll, pitch, and yaw moments at once?	Geon-Hong	OpenFOAM Post-Processing	0	November 22, 2011 00:50
Estimate convection and diffusion terms in transport equation	Lance	CFX	0	April 4, 2011 12:16
Transient Error Estimate with icoErrorEstimate ?	kassiotis	OpenFOAM Post-Processing	1	June 28, 2009 06:24
Unstructured Viscous Time Step Estimate	Anthony Iannetti	Main CFD Forum	8	July 15, 2001 12:24
How to Estimate Numerical Diffusion	Jon Johnson	Main CFD Forum	3	November 4, 1999 15:00

October 4, 2012, 10:35		#4
eng_norouzi Member ali Join Date: Feb 2011 Posts: 37 Rep Power: 15	I know what is this error for I just can't find the option can anybody help me to find it please? maybe my cfx doesn't have it can you check it please

October 4, 2012, 18:21		#5
singer1812 Senior Member Edmund Singer P.E. Join Date: Aug 2010 Location: Minneapolis, MN Posts: 511 Rep Power: 21	Go in the command editor foor Expert Parameters and just type it in as the instructions say. CFX will accept it.

January 23, 2013, 16:10		#6
welaa New Member walid mohammed abdel maged Join Date: Feb 2012 Posts: 4 Rep Power: 14	hi I have the error massage same to above. I used ANSYS v13 want to change topology estimate factor zif . Or how to eliminate this massage