[ICEM] Edge parameters problem

fd99 · April 17, 2012, 08:01

Hello,

I'm new to ICEM so please treat me kindly

I encountered following problem when generating the premesh:

After having generated the initia block, i splited it several times and in the end i got following configuration:

1 2
3 4
5 6

I deleted block 4, because it represents the interior of a wall, which I don't want to simulate, which gave me following config.:

1 2
3
5 6

I did all the assigments and when I change now the edge paratmeters of te horizontal edges of block 6, ICEM channges the node-number of block 2 accordingly. I turned of the 'copy parameters' buton, but it still won't help.

How do I change the horizontal node number of block 6 without changing the number of nodes of block 2?

Thank you very much,

Jan

Far · April 17, 2012, 08:05

I promise to be gentle!

delete block 4 permanently (solution taken from Simon's presentation available on ANSYS portal)

fd99 · April 17, 2012, 08:36

Merci beaucoup Far!

Far · April 17, 2012, 08:37

http://www.kxcad.net/ansys/ANSYS_ICE...leteblock.html

Far · April 17, 2012, 08:39

Merci beaucoup Far! = Thanks a lot Far!

April 17, 2012, 08:01	Edge parameters problem	#1
fd99 New Member Jan H Join Date: Apr 2012 Posts: 2 Rep Power: 0	Hello, I'm new to ICEM so please treat me kindly I encountered following problem when generating the premesh: After having generated the initia block, i splited it several times and in the end i got following configuration: 1 2 3 4 5 6 I deleted block 4, because it represents the interior of a wall, which I don't want to simulate, which gave me following config.: 1 2 3 5 6 I did all the assigments and when I change now the edge paratmeters of te horizontal edges of block 6, ICEM channges the node-number of block 2 accordingly. I turned of the 'copy parameters' buton, but it still won't help. How do I change the horizontal node number of block 6 without changing the number of nodes of block 2? Thank you very much, Jan

April 17, 2012, 08:05		#2
Far Senior Member Sijal Join Date: Mar 2009 Location: Islamabad Posts: 4,558 Blog Entries: 6 Rep Power: 54	I promise to be gentle! delete block 4 permanently (solution taken from Simon's presentation available on ANSYS portal) mkiilerich and onofrio like this.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
how to set periodic boundary conditions	Ganesh	FLUENT	15	November 18, 2020 07:09
Multi element wing 3-d problem: trailing edge resolution	sriram042000	CFX	2	March 13, 2011 06:44
Actuator disk model	audrich	FLUENT	0	September 21, 2009 08:06
Through-Flow solver, Leading-Trailing edge problem	Menander	Main CFD Forum	0	May 14, 2008 19:14
Periodic flow boundary condition problem	sudha	FLUENT	3	April 28, 2004 09:40

April 17, 2012, 08:36		#3
fd99 New Member Jan H Join Date: Apr 2012 Posts: 2 Rep Power: 0	Merci beaucoup Far!

April 17, 2012, 08:37		#4
Far Senior Member Sijal Join Date: Mar 2009 Location: Islamabad Posts: 4,558 Blog Entries: 6 Rep Power: 54	http://www.kxcad.net/ansys/ANSYS_ICE...leteblock.html

April 17, 2012, 08:39		#5
Far Senior Member Sijal Join Date: Mar 2009 Location: Islamabad Posts: 4,558 Blog Entries: 6 Rep Power: 54	Merci beaucoup Far! = Thanks a lot Far!