[ICEM] Different Levels of Refinement in Adjacent Blocks

aero_head · February 3, 2021, 23:29

Hello,

I am doing a refinement of blocks (Blocking > Pre-Mesh Params > Refinement) on my structured mesh.

I have three blocks beside each other and want the middle one to have a 2x refinement and the ones on either side to have a 3x refinement (in the streamwise and spanwise directions).

At first it was giving me an error with something about surface nodes do not match, but I finally found a way to implement this. However, when I tried to resolve the refinements (I tried all three options, standard, allow unsupported and Pure 3D), however they all fail.

Is this possible to do? If so, what am I doing wrong? Do I have to resolve refinements on each block as I go along (i.e. before refining the next one)?

Thanks in advance.

bluebase · February 4, 2021, 15:55

I recall that (element-level) resolving refinements only works with a 3-1 ratio. So 3-2 and 1-2 should not work if i remember correctly.

aero_head · February 4, 2021, 22:09

Hello Sebastian,

Thank you for clearing that up for me. There is not a lot of information on how refinements work in the documentation, IMO. I have read through the ICEM Help and User's Manuals, as well as the tutorials, but could not answer these questions about refinements.

February 3, 2021, 23:29	Different Levels of Refinement in Adjacent Blocks	#1
aero_head Senior Member Kira Join Date: Nov 2020 Location: Canada Posts: 435 Rep Power: 9	Hello, I am doing a refinement of blocks (Blocking > Pre-Mesh Params > Refinement) on my structured mesh. I have three blocks beside each other and want the middle one to have a 2x refinement and the ones on either side to have a 3x refinement (in the streamwise and spanwise directions). At first it was giving me an error with something about surface nodes do not match, but I finally found a way to implement this. However, when I tried to resolve the refinements (I tried all three options, standard, allow unsupported and Pure 3D), however they all fail. Is this possible to do? If so, what am I doing wrong? Do I have to resolve refinements on each block as I go along (i.e. before refining the next one)? Thanks in advance.

February 4, 2021, 15:55		#2
bluebase Senior Member Sebastian Engel Join Date: Jun 2011 Location: Germany Posts: 567 Rep Power: 21	I recall that (element-level) resolving refinements only works with a 3-1 ratio. So 3-2 and 1-2 should not work if i remember correctly. aero_head likes this.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[snappyHexMesh] SnappyHexMesh running killed!	Mark JIN	OpenFOAM Meshing & Mesh Conversion	7	June 14, 2022 02:37
SimpleFoam & Theater	jipai	OpenFOAM Running, Solving & CFD	3	June 18, 2019 11:11
[snappyHexMesh] Error snappyhexmesh - Multiple outside loops	avinashjagdale	OpenFOAM Meshing & Mesh Conversion	53	March 8, 2019 10:42
[Commercial meshers] converting Fluent mesh to openfoam standard mesh	deepesh	OpenFOAM Meshing & Mesh Conversion	31	March 29, 2017 06:59
[snappyHexMesh] snappyHexMesh aborting	Tobi	OpenFOAM Meshing & Mesh Conversion	0	November 10, 2010 04:23

February 4, 2021, 22:09		#3
aero_head Senior Member Kira Join Date: Nov 2020 Location: Canada Posts: 435 Rep Power: 9	Hello Sebastian, Thank you for clearing that up for me. There is not a lot of information on how refinements work in the documentation, IMO. I have read through the ICEM Help and User's Manuals, as well as the tutorials, but could not answer these questions about refinements.