[ANSYS Meshing] Selecting inner faces

jasdeep2006singh · February 24, 2013, 12:45

This might sound like a silly question but how to select an inner surface in a solid.
I am trying to do an aircraft wing analysis. in order to have higher density mesh near the surface of the wing, i am selecting the 'face sizing' option in mesh. it is okay with half wing since the wall is at the root of the wing. how to do 'inside' when the 'wing shaped hole' in inside the control volume.

jrunsten · February 25, 2013, 02:56

Click where you see the surface and then go "trough" other surfaces by selecing the appropriate layer:

Hard to explain in words, but I hope you get it

jasdeep2006singh · February 25, 2013, 06:23

Snap showed it all, thank you very much

xiyuan · June 13, 2018, 23:31

HI is this from Space claim ?

RVL · March 5, 2019, 03:25

You should select the outer faces, then right click and select hide face (F8).
That's how you can have access to inner surfaces.

February 24, 2013, 12:45	Selecting inner faces	#1
jasdeep2006singh New Member Jasdeep Join Date: Oct 2012 Posts: 13 Rep Power: 14	This might sound like a silly question but how to select an inner surface in a solid. I am trying to do an aircraft wing analysis. in order to have higher density mesh near the surface of the wing, i am selecting the 'face sizing' option in mesh. it is okay with half wing since the wall is at the root of the wing. how to do 'inside' when the 'wing shaped hole' in inside the control volume.

February 25, 2013, 02:56		#2
jrunsten Senior Member Josef Runsten Join Date: Jul 2010 Location: Gothenburg, Sweden Posts: 188 Rep Power: 24	Click where you see the surface and then go "trough" other surfaces by selecing the appropriate layer: Hard to explain in words, but I hope you get it reza2031 and ddossant like this.

February 25, 2013, 06:23	Thank you	#3
jasdeep2006singh New Member Jasdeep Join Date: Oct 2012 Posts: 13 Rep Power: 14	Snap showed it all, thank you very much

March 5, 2019, 03:25	For Ansys Fluent	#5
RVL New Member Rudra Lad Join Date: Mar 2019 Posts: 1 Rep Power: 0	You should select the outer faces, then right click and select hide face (F8). That's how you can have access to inner surfaces. reza2031, t1333 and MITHRIL like this.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[snappyHexMesh] Add Mesh Layers doesnt work on the whole surface	Kryo	OpenFOAM Meshing & Mesh Conversion	13	February 17, 2022 08:34
[Other] Mesh Importing Problem	cuteapathy	ANSYS Meshing & Geometry	2	June 24, 2017 06:29
[snappyHexMesh] No layers in a small gap	bobburnquist	OpenFOAM Meshing & Mesh Conversion	6	August 26, 2015 10:38
[snappyHexMesh] snappyHexMesh won't work - zeros everywhere!	sc298	OpenFOAM Meshing & Mesh Conversion	2	March 27, 2011 22:11
[snappyHexMesh] external flow with snappyHexMesh	chelvistero	OpenFOAM Meshing & Mesh Conversion	11	January 15, 2010 20:43

June 13, 2018, 23:31		#4
xiyuan New Member changxiyuan Join Date: Jun 2018 Posts: 3 Rep Power: 8	HI is this from Space claim ?