[ICEM] ICEM Challenge - Wing mesh

Far · June 7, 2012, 12:39

Here is the geometry of typical tapered wing. Every one is invited to participate in this challenge. I will show you my mesh soon.

BrolY · June 8, 2012, 05:10

You have already given the .blk file inside your .zip file lol

Far · June 8, 2012, 05:12

It is just blocking with few splits. no association and anything else.

.

I guess it is very much difficult to block this wing with quality.

everdimension · June 8, 2012, 07:53

A screenshot of initial geometry would attract and entice more

Far · June 8, 2012, 08:12

Quote:

entice more

Are you talking of screen shot of jenefer lopez on the floor

everdimension · June 8, 2012, 08:13

)))) well, if your wing geometry has the same effect it certainly wouldn't hurt ))

Far · June 8, 2012, 08:17

Ok. I shall place a screen shot today.

diamondx · June 8, 2012, 10:17

is there a price ?

Far · June 8, 2012, 12:20

Yes. You will get job at Far Inc.

cfd seeker · June 27, 2012, 12:14

have you managed to get good blocking for this geometry?

Far · June 27, 2012, 12:14

yes.............

cfd seeker · June 27, 2012, 12:21

Great......kindly place your blocking files here so that others can take benefit from it

June 8, 2012, 10:17		#8
diamondx Super Moderator Ghazlani M. Ali Join Date: May 2011 Location: Tokyo, Japan Posts: 1,385 Blog Entries: 23 Rep Power: 29	is there a price ? __________________ Regards, New to ICEM CFD, try this document --> https://goo.gl/KAOIwm Ali

June 8, 2012, 12:20		#9
Far Senior Member Sijal Join Date: Mar 2009 Location: Islamabad Posts: 4,558 Blog Entries: 6 Rep Power: 54	Yes. You will get job at Far Inc. diamondx likes this.

June 27, 2012, 12:14		#11
Far Senior Member Sijal Join Date: Mar 2009 Location: Islamabad Posts: 4,558 Blog Entries: 6 Rep Power: 54	yes............. Melvins likes this.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
how to set periodic boundary conditions	Ganesh	FLUENT	15	November 18, 2020 07:09
mesh missing after export in gambit	morteza08	ANSYS Meshing & Geometry	1	July 26, 2010 02:10
problem when converting mesh (made by ICEM) using fluentMeshToFoam	Forrest_Lei	OpenFOAM	11	October 16, 2009 07:28
Boddy fitted Hexcore Mesh in ICEM Cfd	Mitch	CFX	0	December 29, 2008 07:07
Mesh from ICEM CFD to CFX ! Error ! Why ? Thanks !	Vu Trinh Tuan	CFX	11	March 28, 2005 20:04

June 8, 2012, 05:10		#2
BrolY Senior Member AB Join Date: Sep 2009 Location: France Posts: 323 Rep Power: 22	You have already given the .blk file inside your .zip file lol

June 8, 2012, 05:12		#3
Far Senior Member Sijal Join Date: Mar 2009 Location: Islamabad Posts: 4,558 Blog Entries: 6 Rep Power: 54	It is just blocking with few splits. no association and anything else. . I guess it is very much difficult to block this wing with quality.

June 8, 2012, 07:53		#4
everdimension New Member Join Date: May 2012 Location: Moscow Posts: 27 Rep Power: 14	A screenshot of initial geometry would attract and entice more

June 8, 2012, 08:13		#6
everdimension New Member Join Date: May 2012 Location: Moscow Posts: 27 Rep Power: 14	)))) well, if your wing geometry has the same effect it certainly wouldn't hurt ))

June 8, 2012, 08:17		#7
Far Senior Member Sijal Join Date: Mar 2009 Location: Islamabad Posts: 4,558 Blog Entries: 6 Rep Power: 54	Ok. I shall place a screen shot today.

June 27, 2012, 12:14		#10
cfd seeker Senior Member Join Date: Mar 2011 Location: Germany Posts: 552 Rep Power: 20	have you managed to get good blocking for this geometry?

June 27, 2012, 12:21		#12
cfd seeker Senior Member Join Date: Mar 2011 Location: Germany Posts: 552 Rep Power: 20	Great......kindly place your blocking files here so that others can take benefit from it