[rfadlika]

Hi everyone,

I've installed SU2--master in server, there is no problem in the installation. When I run Quick Start cases I got this errors :


A requested component was not found, or was unable to be opened. This
means that this component is either not installed or is unable to be
used on your system (e.g., sometimes this means that shared libraries
that the component requires are unable to be found/loaded). Note that
Open MPI stopped checking at the first component that it did not find.

Host: server
Framework: crs
Component: none
--------------------------------------------------------------------------
[server:24496] *** Process received signal ***
[server:24496] Signal: Segmentation fault (11)
[server:24496] Signal code: Address not mapped (1)
[server:24496] Failing at address: 0x28
[server:24496] [ 0] /lib/x86_64-linux-gnu/libpthread.so.0(+0xf0a0) [0x7fcd04d710a0]
[server:24496] [ 1] /usr/lib/libopen-pal.so.0(mca_base_select+0x106) [0x7fcd05d5f356]
[server:24496] [ 2] /usr/lib/libopen-pal.so.0(opal_crs_base_select+0x7e) [0x7fcd05d7159e]
[server:24496] [ 3] /usr/lib/libopen-pal.so.0(opal_cr_init+0x303) [0x7fcd05d50293]
[server:24496] [ 4] /usr/lib/libopen-pal.so.0(opal_init+0x17b) [0x7fcd05d4fc0b]
[server:24496] [ 5] /usr/lib/libopen-rte.so.0(orte_init+0x4f) [0x7fcd05fa1b3f]
[server:24496] [ 6] /usr/lib/libmpi.so.0(+0x38374) [0x7fcd06219374]
[server:24496] [ 7] /usr/lib/libmpi.so.0(MPI_Init+0x16b) [0x7fcd0623a01b]
[server:24496] [ 8] SU2_CFD(main+0x58) [0x4b7768]
[server:24496] [ 9] /lib/x86_64-linux-gnu/libc.so.6(__libc_start_main+0xfd) [0x7fcd049f5ead]
[server:24496] [10] SU2_CFD() [0x4b985d]
[server:24496] *** End of error message ***
Segmentation fault




Regards,
Ridwan

[talbring]

Hi rfadlika,

can you give me some information ?

- operating system
- SU2 version
- configure options
- command that you used to run the case
- the complete output of SU2_CFD

Thanks !

[rfadlika]

Originally Posted by talbring

Hi rfadlika,

can you give me some information ?

- operating system
- SU2 version
- configure options
- command that you used to run the case
- the complete output of SU2_CFD

Thanks !

Hi talbring,

OS: Linux Mint 17.1
SU2 version (I do not know the version, but it is not educational version and I get from github SU2-master)
Configure options is according to the tutorial Quick Start
Command : SU2_CFD filename.cfg
There is no output yet

The Installation type is 'Parallel and CGNS'

Thanks

[dev1656]

Hey Ridwan,

I would suggest you to reinstall Su2 but before that make sure you use make clean for cleaning previous file and this time before installing it make a note that you have all the prerequisite like g++(updated lib) and if you are trying for parallel make sure you have installed MPICH correctly as sometime it may give an error!!

Best
Ozil!!