How to export mesh from AcuSolve/AcuConsole to Hypermesh/Hyperwork ?

gaddora165 · June 26, 2020, 13:51

anyone has tried to export a mesh from Acuconsole to hypermesh ?
I've built a model in AcuConsole and completed the mesh operation and I'd like to use the same mesh as input into Hypermesh.

I've managed to export the MESH.DIR but this file does not seems can be imported to hypermesh/hyperwork.

I could not manage to find any tutorials about this as well.

pls help !

gaddora165 · June 27, 2020, 01:41

I have exported ".h3d" results from AcuSolve and then imported to SimLab.
then I've exported solver deck ".fem" and then open it through hypermesh.
I have applied all constraints and forces required for the model and then I've run the simulation but I've found an error :

*** WARNING # 1284
No SPC or SUPORT1 data specified for static SUBCASE 1.
Make sure the model is constrained otherwise.

*** ERROR 13: Element, 1 is repeated in the input data.
*** ERROR 13: Element, 2 is repeated in the input data.
*** ERROR 13: Element, 3 is repeated in the input data.
*** ERROR 13: Element, 4 is repeated in the input data.
*** ERROR 13: Element, 5 is repeated in the input data.
*** ERROR 13: Element, 6 is repeated in the input data.
*** ERROR 13: Element, 7 is repeated in the input data.
*** ERROR 13: Element, 8 is repeated in the input data.
*** ERROR 13: Element, 9 is repeated in the input data.
*** ERROR 13: Element, 10 is repeated in the input data.
*** ERROR 13: Element, 11 is repeated in the input data.
*** ERROR 13: Element, 12 is repeated in the input data.
*** ERROR 13: Element, 13 is repeated in the input data.
*** ERROR 13: Element, 14 is repeated in the input data.
*** ERROR 13: Element, 15 is repeated in the input data.

*** ERROR # 1938 ***
Element has repeat IDs 77963 time(s).

is this due to wrong importing/exporting steps that I've done ?
if yes, how would this work ?

gaddora165 · June 27, 2020, 01:44

error messages from the .OUT file as per below:

*** WARNING # 1284
No SPC or SUPORT1 data specified for static SUBCASE 1.
Make sure the model is constrained otherwise.

*** ERROR 13: Element, 1 is repeated in the input data.
*** ERROR 13: Element, 2 is repeated in the input data.
*** ERROR 13: Element, 3 is repeated in the input data.
*** ERROR 13: Element, 4 is repeated in the input data.
*** ERROR 13: Element, 5 is repeated in the input data.
*** ERROR 13: Element, 6 is repeated in the input data.
*** ERROR 13: Element, 7 is repeated in the input data.
*** ERROR 13: Element, 8 is repeated in the input data.
*** ERROR 13: Element, 9 is repeated in the input data.
*** ERROR 13: Element, 10 is repeated in the input data.
*** ERROR 13: Element, 11 is repeated in the input data.
*** ERROR 13: Element, 12 is repeated in the input data.
*** ERROR 13: Element, 13 is repeated in the input data.
*** ERROR 13: Element, 14 is repeated in the input data.
*** ERROR 13: Element, 15 is repeated in the input data.

*** ERROR # 1938 ***
Element has repeat IDs 77963 time(s).

June 26, 2020, 13:51	How to export mesh from AcuSolve/AcuConsole to Hypermesh/Hyperwork ?	#1
gaddora165 New Member Mohamed Join Date: Jan 2019 Posts: 21 Rep Power: 7	anyone has tried to export a mesh from Acuconsole to hypermesh ? I've built a model in AcuConsole and completed the mesh operation and I'd like to use the same mesh as input into Hypermesh. I've managed to export the MESH.DIR but this file does not seems can be imported to hypermesh/hyperwork. I could not manage to find any tutorials about this as well. pls help !

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
sliding mesh problem in CFX	Saima	CFX	46	September 11, 2021 08:38
A CFX-POST error (ver 14.5.7)	wangyflp88	CFX	2	July 22, 2017 01:17
Moving mesh	Niklas Wikstrom (Wikstrom)	OpenFOAM Running, Solving & CFD	122	June 15, 2014 07:20
Export 2D mesh from ICEM to Fluent	BuilttoSpill	ANSYS Meshing & Geometry	4	August 28, 2010 09:16
fluent add additional zones for the mesh file	SSL	FLUENT	2	January 26, 2008 12:55

June 27, 2020, 01:41		#2
gaddora165 New Member Mohamed Join Date: Jan 2019 Posts: 21 Rep Power: 7	I have exported ".h3d" results from AcuSolve and then imported to SimLab. then I've exported solver deck ".fem" and then open it through hypermesh. I have applied all constraints and forces required for the model and then I've run the simulation but I've found an error : * WARNING # 1284 No SPC or SUPORT1 data specified for static SUBCASE 1. Make sure the model is constrained otherwise. * ERROR 13: Element, 1 is repeated in the input data. * ERROR 13: Element, 2 is repeated in the input data. * ERROR 13: Element, 3 is repeated in the input data. * ERROR 13: Element, 4 is repeated in the input data. * ERROR 13: Element, 5 is repeated in the input data. * ERROR 13: Element, 6 is repeated in the input data. * ERROR 13: Element, 7 is repeated in the input data. * ERROR 13: Element, 8 is repeated in the input data. * ERROR 13: Element, 9 is repeated in the input data. * ERROR 13: Element, 10 is repeated in the input data. * ERROR 13: Element, 11 is repeated in the input data. * ERROR 13: Element, 12 is repeated in the input data. * ERROR 13: Element, 13 is repeated in the input data. * ERROR 13: Element, 14 is repeated in the input data. * ERROR 13: Element, 15 is repeated in the input data. * ERROR # 1938 * Element has repeat IDs 77963 time(s). is this due to wrong importing/exporting steps that I've done ? if yes, how would this work ?

June 27, 2020, 01:44		#3
gaddora165 New Member Mohamed Join Date: Jan 2019 Posts: 21 Rep Power: 7	error messages from the .OUT file as per below: * WARNING # 1284 No SPC or SUPORT1 data specified for static SUBCASE 1. Make sure the model is constrained otherwise. * ERROR 13: Element, 1 is repeated in the input data. * ERROR 13: Element, 2 is repeated in the input data. * ERROR 13: Element, 3 is repeated in the input data. * ERROR 13: Element, 4 is repeated in the input data. * ERROR 13: Element, 5 is repeated in the input data. * ERROR 13: Element, 6 is repeated in the input data. * ERROR 13: Element, 7 is repeated in the input data. * ERROR 13: Element, 8 is repeated in the input data. * ERROR 13: Element, 9 is repeated in the input data. * ERROR 13: Element, 10 is repeated in the input data. * ERROR 13: Element, 11 is repeated in the input data. * ERROR 13: Element, 12 is repeated in the input data. * ERROR 13: Element, 13 is repeated in the input data. * ERROR 13: Element, 14 is repeated in the input data. * ERROR 13: Element, 15 is repeated in the input data. * ERROR # 1938 * Element has repeat IDs 77963 time(s).