Velocity monitoring in Star-CCM+ after the simulation conducted

aroma · January 1, 2016, 14:46

Hi folks,

I have a problem in drawing the velocity vs. time after a transient simulation is done.
I have conducted a transient simulation and it is converged. I've created several point probes and monitored the pressure. So I have the pressure vs time curves for those points.
However, I have these two problems:
1- how can I have velocity vs. time at the predefined points? I've been changing the corresponding report function to Velocity but I wouldn't got any curve.
By the way, I have already defined the Solution History and the velocity has been recorded.
2- can I define new point probe after the simulation is done? and how?

Thanks a lot for your help.

Cheers,
Aroma

fluid23 · January 4, 2016, 13:21

you can use the same probe points and just create a velocity report for each one. however, as far as I know you cannot setup a report after the simulation has been run and expect to capture any data previous to the creation of the report. if you need velocity and pressure across the whole time domain then you will need to re run the analysis.

aroma · January 4, 2016, 17:26

Quote:

Originally Posted by MBdonCFD

you can use the same probe points and just create a velocity report for each one. however, as far as I know you cannot setup a report after the simulation has been run and expect to capture any data previous to the creation of the report. if you need velocity and pressure across the whole time domain then you will need to re run the analysis.

Thank you Matt.
I have saved/recorded the velocity in the solution history though. I was hoping I could use that.

fluid23 · January 4, 2016, 17:42

hmm... I am not sure, but I still think that your reports will only work moving forward. have you tried checking the steve portal to see if there was anything posted there?

January 1, 2016, 14:46	Velocity monitoring in Star-CCM+ after the simulation conducted	#1
aroma New Member Hamed Join Date: Jul 2012 Posts: 16 Rep Power: 14	Hi folks, I have a problem in drawing the velocity vs. time after a transient simulation is done. I have conducted a transient simulation and it is converged. I've created several point probes and monitored the pressure. So I have the pressure vs time curves for those points. However, I have these two problems: 1- how can I have velocity vs. time at the predefined points? I've been changing the corresponding report function to Velocity but I wouldn't got any curve. By the way, I have already defined the Solution History and the velocity has been recorded. 2- can I define new point probe after the simulation is done? and how? Thanks a lot for your help. Cheers, Aroma

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Simulation of radial gas turbine, Inlet velocity components	dmaz	CFX	17	May 19, 2019 10:45
Monitoring Volume Average of Liquid Velocity Magnitude in a Bubble Column / Airlift	kevinlipps	OpenFOAM Post-Processing	4	May 19, 2016 06:59
Run time monitoring of velocity or flux	File	OpenFOAM Running, Solving & CFD	3	May 19, 2016 06:58
Problem mesh importing to STAR CCM	mohammad	Mesh Generation & Pre-Processing	0	January 19, 2015 23:45
Condition of Air velocity in Open Channel simulation	wes1204	OpenFOAM Running, Solving & CFD	0	May 9, 2014 06:08

January 4, 2016, 13:21		#2
fluid23 Senior Member Matt Join Date: Aug 2014 Posts: 947 Rep Power: 18	you can use the same probe points and just create a velocity report for each one. however, as far as I know you cannot setup a report after the simulation has been run and expect to capture any data previous to the creation of the report. if you need velocity and pressure across the whole time domain then you will need to re run the analysis.

January 4, 2016, 17:42		#4
fluid23 Senior Member Matt Join Date: Aug 2014 Posts: 947 Rep Power: 18	hmm... I am not sure, but I still think that your reports will only work moving forward. have you tried checking the steve portal to see if there was anything posted there?