Opening a Simulation file using JAVA Macro

Vibh · April 1, 2015, 09:39

Hi! I am writing a JAVA Macro for performing an arithmetic operation on an exported X,Y,Z Coordinates' file from STAR CCM+ to get a new set of X,Y and Z. To do so, I need to open in between a different Simulation file.
(For ex- If I have presently opened File0.sim, and on which my JAVA Macro is currently executing its commands. How do I, from Macro, open a different Simulation File1.sim?)
Is there a way to do this?

Any suggestion would be highly helpful!
Thank you!

TimCFD · April 4, 2015, 07:47

I´m not an expert in Java scripting, but the starting point for me is always a recording. In your case File0.sim is open, start to record a Java macro, go to files, load simulation File1.sim, stop recording and have a look at the macro.

Two simulations are now open in your GUI and you can perform the next steps.

yxiang · June 1, 2022, 11:59

1. Open new session from a sim file (return nothing and scripts does not wait):

star.coremodule.OpenFile.open(simPath);
// wait seconds for fully initilizing
// the new session become active automatically.
Simulation sim=getActiveSimulation();

2. Get Simulation object from a sim file(doesn't visually open in a session):

Simulation sim = new Simulation(simPath);
// do something then close it...
sim.close(star.base.neo.ServerConnection.CloseOpti on.ForceClose);

April 1, 2015, 09:39	Opening a Simulation file using JAVA Macro	#1
Vibh New Member Vibhor pandey Join Date: Aug 2014 Posts: 3 Rep Power: 12	Hi! I am writing a JAVA Macro for performing an arithmetic operation on an exported X,Y,Z Coordinates' file from STAR CCM+ to get a new set of X,Y and Z. To do so, I need to open in between a different Simulation file. (For ex- If I have presently opened File0.sim, and on which my JAVA Macro is currently executing its commands. How do I, from Macro, open a different Simulation File1.sim?) Is there a way to do this? Any suggestion would be highly helpful! Thank you!

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[swak4Foam] funkyDoCalc with OF2.3 massflow	NiFl	OpenFOAM Community Contributions	14	November 25, 2020 04:30
what is swap4foam ??	AB08	OpenFOAM	28	February 2, 2016 02:22
[swak4Foam] swak4Foam-groovyBC build problem	zxj160	OpenFOAM Community Contributions	18	July 30, 2013 14:14
[swak4Foam] build problem swak4Foam OF 2.2.0	mcathela	OpenFOAM Community Contributions	14	April 23, 2013 14:59
[blockMesh] Axisymmetrical mesh	Rasmus Gjesing (Gjesing)	OpenFOAM Meshing & Mesh Conversion	10	April 2, 2007 15:00

April 4, 2015, 07:47		#2
TimCFD New Member Tim Meier Join Date: Mar 2015 Posts: 16 Rep Power: 11	I´m not an expert in Java scripting, but the starting point for me is always a recording. In your case File0.sim is open, start to record a Java macro, go to files, load simulation File1.sim, stop recording and have a look at the macro. Two simulations are now open in your GUI and you can perform the next steps.

June 1, 2022, 11:59		#3
yxiang New Member yang Join Date: Jun 2022 Posts: 1 Rep Power: 0	1. Open new session from a sim file (return nothing and scripts does not wait): star.coremodule.OpenFile.open(simPath); // wait seconds for fully initilizing // the new session become active automatically. Simulation sim=getActiveSimulation(); 2. Get Simulation object from a sim file(doesn't visually open in a session): Simulation sim = new Simulation(simPath); // do something then close it... sim.close(star.base.neo.ServerConnection.CloseOpti on.ForceClose);