COMANDS TO EXPORT GAMBIT MESH IN PROSTAR3100A

February 8, 2001, 07:50

I'd like to know the best exportation format file for Gambit and the correct comands to import it!

February 8, 2001, 17:57

Read the Gambit neutral file or mesh file into Tgrid.

From Tgrid, write out a Patran file.

Import the Patran file into Prostar.

Chinor

February 9, 2001, 04:56

What's this "Tgrid" ,is it acomand of Gambit? Sorry for the stupid question but I'm a beginner! However thankyou Chinor

February 9, 2001, 15:38

Tgrid is another pre-processor for Fluent.

You should check with your software custodian to see if you have this piece of software.

Chinor

February 12, 2001, 13:44

Save your gambit mesh in neutral and in star-cd, in the command line, type the command : gambit nameofyourmesh.neu

February 13, 2001, 13:58

hvn

I tried that and Prostar (v3100a) crashed.

Did you actually do this successfully?

Chinor

February 15, 2001, 06:05

with 3100A cruched, with 3100 didn't cruch but it isn't successful!

February 20, 2001, 13:08

I used this command with prostar v3100 and there was no problem. The mesh in prostar was identically as in fluent 5 and in Gambit

February 8, 2001, 07:50	COMANDS TO EXPORT GAMBIT MESH IN PROSTAR3100A	#1
Cerioni Guest Posts: n/a	I'd like to know the best exportation format file for Gambit and the correct comands to import it!

February 8, 2001, 17:57	Re: COMANDS TO EXPORT GAMBIT MESH IN PROSTAR3100A	#2
Chinor Guest Posts: n/a	Read the Gambit neutral file or mesh file into Tgrid. From Tgrid, write out a Patran file. Import the Patran file into Prostar. Chinor

February 9, 2001, 04:56	Re: COMANDS TO EXPORT GAMBIT MESH IN PROSTAR3100A	#3
Cerioni Guest Posts: n/a	What's this "Tgrid" ,is it acomand of Gambit? Sorry for the stupid question but I'm a beginner! However thankyou Chinor

February 9, 2001, 15:38	Re: COMANDS TO EXPORT GAMBIT MESH IN PROSTAR3100A	#4
Chinor Guest Posts: n/a	Tgrid is another pre-processor for Fluent. You should check with your software custodian to see if you have this piece of software. Chinor

February 12, 2001, 13:44	Re: COMANDS TO EXPORT GAMBIT MESH IN PROSTAR3100A	#5
hvn Guest Posts: n/a	Save your gambit mesh in neutral and in star-cd, in the command line, type the command : gambit nameofyourmesh.neu

February 13, 2001, 13:58	Re: COMANDS TO EXPORT GAMBIT MESH IN PROSTAR3100A	#6
Chinor Guest Posts: n/a	hvn I tried that and Prostar (v3100a) crashed. Did you actually do this successfully? Chinor

February 15, 2001, 06:05	Re: COMANDS TO EXPORT GAMBIT MESH IN PROSTAR3100A	#7
Cerioni Guest Posts: n/a	with 3100A cruched, with 3100 didn't cruch but it isn't successful!

February 20, 2001, 13:08	Re: COMANDS TO EXPORT GAMBIT MESH IN PROSTAR3100A	#8
hvn Guest Posts: n/a	I used this command with prostar v3100 and there was no problem. The mesh in prostar was identically as in fluent 5 and in Gambit