|
[Sponsors] |
February 8, 2023, 01:24 |
Sand slide algorithm
|
#1 |
Member
Ajay Jatoliya
Join Date: Nov 2022
Posts: 65
Rep Power: 3 |
Hello REEF 3D Team,
In S 93, what should be Delta angle for landslide correction, default value is 0.0. as many of papers mention correction = -2.0 So which one is correct, S 93 2.0 or S 93 -2.0 ? And what is S 81 and S 82 parameters. |
|
February 9, 2023, 16:37 |
|
#2 |
Super Moderator
Hans Bihs
Join Date: Jun 2009
Location: Trondheim, Norway
Posts: 396
Rep Power: 18 |
Use the positive number for S 92, that will work.
S 81: angle of repose phi S 82: delta phi, will reduce phi for uphill flow and increase it for downhill flow |
|
February 10, 2023, 07:52 |
|
#3 |
Member
Ajay Jatoliya
Join Date: Nov 2022
Posts: 65
Rep Power: 3 |
Thank you, sir, for your reply
Now I am confused between parameters S 25 and S 81. if both are the same parameters which are the angle of repose, then in the reef 3d manual, it has different default values S 25 30 S 81 35 the angle of repose in my condition is 30 degrees, so do I need to put S 25 30? and if I am choosing correction = 2 degree Then do I need to put S 93 2, S 81 32(30+2) and S 82 2? |
|
February 10, 2023, 11:19 |
|
#4 |
Super Moderator
Hans Bihs
Join Date: Jun 2009
Location: Trondheim, Norway
Posts: 396
Rep Power: 18 |
Hi Ajay,
not sure you mean S 25, as it does not exist. |
|
February 10, 2023, 12:27 |
|
#5 |
Member
Ajay Jatoliya
Join Date: Nov 2022
Posts: 65
Rep Power: 3 |
Ok, thank you, sir, for clearing my doubt. as I am using REEF 3D version 22.04. In the REEF 3D manual, there is an S 25 parameter which is for the angle of repose.
|
|
February 10, 2023, 12:31 |
|
#6 |
Super Moderator
Hans Bihs
Join Date: Jun 2009
Location: Trondheim, Norway
Posts: 396
Rep Power: 18 |
Please use 23.01. In general: always go with the newest version.
In 23.01, S 25 is removed and sediment transport modeling is improved. For bed shear stress have a look at S 16 4. |
|
February 10, 2023, 13:03 |
|
#7 |
Member
Ajay Jatoliya
Join Date: Nov 2022
Posts: 65
Rep Power: 3 |
Yes, sir, I got it
Thanks for your valuable suggestion |
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Help with PIMPLE algorithm in chtMultiregionFoam | Chris T | OpenFOAM Running, Solving & CFD | 0 | August 30, 2022 08:49 |
rhoSimplecFoam - which algorithm is implemented - references | Manuel CFD | OpenFOAM Programming & Development | 7 | September 8, 2014 07:28 |
[OpenFOAM] Paraview 3.98 - errors when saving geometry file | pajot | ParaView | 1 | September 28, 2013 10:45 |
About Phase Coupled SIMPLE (PC-SIMPLE) algorithm | Yan Kai | Main CFD Forum | 0 | April 18, 2007 03:48 |
About Phase Coupled SIMPLE (PC-SIMPLE) algorithm | Yan Kai | FLUENT | 0 | April 13, 2007 23:17 |