[OpenFOAM] Paraview chrashed by using "plot over line"

preibie · November 15, 2011, 07:59

Hallo

I have a little Problem with paraview 3.10. When I want to use the filter "plot over line" paraview stopped and the following massage is on the shell.

Code:

X Error: BadLength (poly request too large or internal Xlib length error) 16
  Extension:    135 (Uknown extension)
  Minor opcode: 1 (Unknown request)
  Resource id:  0x3803ec3
libxcb: WARNING! Program tries to lock an already locked connection,
        which indicates a programming error.
        There will be no further warnings about this issue.

I use paraview via ssh.

Preibie

olivierG · November 15, 2011, 08:57

hello,

Paraview doesn't work well in ssh -X, VNC or NX distant connection, specialy with "plot over lines" and some other function.

You may try to mount the distant dir via sshfs and run paraview directly on your pc, or use paraview in remote configuration.

regards,
olivier

preibie · November 15, 2011, 09:30

thanks for the fast help. You say that it is possible to run paraview in remote configuration. How I can do this?

olivierG · November 15, 2011, 10:00

hello,

take a look at http://www.itk.org/Wiki/Users_Guide_..._Visualization and http://www.itk.org/Wiki/ParaView/Use...rallel_Servers
If you use an ssh acces on non local network, you may use ssh port forwarding.

Regards,
olivier

preibie · November 18, 2011, 04:50

this was a very good idea! Now I can use plot over line

Thanks Preibie

November 15, 2011, 07:59	Paraview chrashed by using "plot over line"	#1
preibie Member Stefan Join Date: Jun 2009 Posts: 67 Rep Power: 17	Hallo I have a little Problem with paraview 3.10. When I want to use the filter "plot over line" paraview stopped and the following massage is on the shell. Code: X Error: BadLength (poly request too large or internal Xlib length error) 16 Extension: 135 (Uknown extension) Minor opcode: 1 (Unknown request) Resource id: 0x3803ec3 libxcb: WARNING! Program tries to lock an already locked connection, which indicates a programming error. There will be no further warnings about this issue. I use paraview via ssh. Preibie

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[OpenFOAM] Plot over line average magnitude of particle velocity in paraview	maysmech	ParaView	13	August 12, 2022 12:46
[Gmsh] Problem with Gmsh	nishant_hull	OpenFOAM Meshing & Mesh Conversion	23	August 5, 2015 03:09
[General] 2 datas on one plot	Akuji	ParaView	46	December 1, 2013 15:06
OpenFOAM 1.7.1 installation problem on OpenSUSE 11.3	flakid	OpenFOAM Installation	16	December 28, 2010 09:48
Problems of Duns Codes!	Martin J	Main CFD Forum	8	August 15, 2003 00:19

November 15, 2011, 08:57		#2
olivierG Senior Member Olivier Join Date: Jun 2009 Location: France, grenoble Posts: 272 Rep Power: 18	hello, Paraview doesn't work well in ssh -X, VNC or NX distant connection, specialy with "plot over lines" and some other function. You may try to mount the distant dir via sshfs and run paraview directly on your pc, or use paraview in remote configuration. regards, olivier

November 15, 2011, 09:30		#3
preibie Member Stefan Join Date: Jun 2009 Posts: 67 Rep Power: 17	thanks for the fast help. You say that it is possible to run paraview in remote configuration. How I can do this?

November 15, 2011, 10:00		#4
olivierG Senior Member Olivier Join Date: Jun 2009 Location: France, grenoble Posts: 272 Rep Power: 18	hello, take a look at http://www.itk.org/Wiki/Users_Guide_..._Visualization and http://www.itk.org/Wiki/ParaView/Use...rallel_Servers If you use an ssh acces on non local network, you may use ssh port forwarding. Regards, olivier

November 18, 2011, 04:50		#5
preibie Member Stefan Join Date: Jun 2009 Posts: 67 Rep Power: 17	this was a very good idea! Now I can use plot over line Thanks Preibie