OpenFOAM

Rating Thread / Thread Starter	Last Post	Replies	Views
Sticky: Getting Started with OpenFOAM ( 1 2) wyldckat	June 21, 2024 07:54 by Martin_Sz	26	52,881
Sticky: OpenFOAM.com versus OpenFOAM.org: Which version to use? wyldckat	March 25, 2023 08:50 by ancolli	19	63,879
Sticky: Map of the OpenFOAM Forum - Understanding where to post your questions! wyldckat	September 2, 2021 06:29 by hakosaj	10	22,138
Sticky: How to contribute to the community of OpenFOAM users and to the OpenFOAM technology wyldckat	November 10, 2017 16:54 by rdbisme	17	21,157
Sticky: How to give enough info to get help linnemann	September 20, 2017 10:19 by linnemann	8	56,886
Sticky: Wiki ( 1 2 3 ... Last Page) gschaider	December 31, 2014 08:34 by wyldckat	178	69,410
[Thank you for help] How comes this modified lapalacianFoam can not be 'wmake'? merlyn	March 6, 2011 16:17 by merlyn	4	1,958
interTrackFoam for rising bubble michielm	March 6, 2011 13:27 by gwierink	3	2,791
ParaFoam, blockMesh etc in vnc SimonH.	March 6, 2011 12:27 by waku2005	1	2,397
Calculator after GroupDatasets doesn't work Hunky	March 5, 2011 12:49 by Hunky	0	1,367
Look for mass fraction Argen	March 5, 2011 08:05 by Rickard.Solsjo	1	1,208
[Thank you for Help] Error occurred when I used wmake merlyn	March 4, 2011 20:56 by merlyn	2	2,340
calculated velocity profile as new wall boundary wouter	March 4, 2011 19:55 by wouter	0	1,580
LES with OpenFOAM samiam1000	March 4, 2011 11:19 by francescomarra	1	2,351
problem when I import mesh with cyclic graduated BC Cyp	March 3, 2011 11:38 by Cyp	0	1,438
Boundary condition for bifurcated flow jiejie	March 3, 2011 11:35 by jose_rodrig	12	5,374
waveBC + pb with "libBoundaryConditions.so" FLOAT	March 3, 2011 10:05 by FLOAT	0	1,543
turbinSiting - disk area snippsnuske	March 3, 2011 08:33 by snippsnuske	0	1,190
wind turbine, actuationDisk snippsnuske	March 3, 2011 08:16 by snippsnuske	1	2,590
BC for simpleSRFFoam kurne	March 3, 2011 07:14 by kurne	0	1,182
How use new case? FLOAT	March 3, 2011 06:32 by FLOAT	0	1,133
timeVarying and surfaceNormal values at the same time lfbarcelo	March 3, 2011 04:53 by bephi	1	2,097
Git for openFoam 1.6-ext? Peter_600	March 3, 2011 03:43 by Chris Lucas	4	2,849
limiter to control velocity ksv	March 2, 2011 19:55 by ksv	0	1,132
OpenFOAM-1.5-Dev kurne	March 2, 2011 18:56 by wouter	1	1,368
gradient at the border ginette	March 2, 2011 15:55 by ginette	0	1,349
Some injectors not injecting parcels usergk	March 2, 2011 14:11 by usergk	0	1,170
Boundary Layer Tripping deji	March 2, 2011 10:24 by deji	0	1,571
Laplacian and 1D flow AlmostSurelyRob	March 2, 2011 10:04 by AlmostSurelyRob	0	1,550
MultiRegionFoam alvora	March 2, 2011 08:40 by alvora	0	2,031
Curvature of the interface using interFoam Andrea_85	March 2, 2011 05:19 by Andrea_85	1	2,909
segmentation error isabel	March 2, 2011 03:25 by isabel	4	1,524
GGI initial value definition: any effect? lordvon	March 2, 2011 02:01 by kurne	11	2,174
Output species data Argen	March 1, 2011 14:56 by Argen	0	1,449
how to use paraview Akuji	March 1, 2011 14:37 by Akuji	5	6,651
buoyantPimpleFoam with free surface (like interFoam) Andreas.Herwig	March 1, 2011 13:07 by Andreas.Herwig	0	2,191
Setting volume fraction in a specific block? tbolt427	March 1, 2011 09:23 by tbolt427	2	1,228
A newbie need your help with gratitude merlyn	February 28, 2011 21:52 by chegdan	1	1,379
Instructors for OpenFOAM University egp	February 28, 2011 16:17 by egp	4	3,240
Maximum parameter values in OpenFOAM vetnav	February 28, 2011 14:28 by lyes43	1	1,672
janafThermo Error/Calculation script? CST	February 28, 2011 07:50 by CST	0	1,510
export force on all cells on a wall ksv	February 27, 2011 09:57 by ksv	0	1,494
What mesh is required? klausb	February 26, 2011 18:34 by klausb	0	1,296
Plot of the turbulent viscosity lift86	February 26, 2011 16:00 by lift86	2	1,956
Quasi-2D mesh with gridgen for 2D RANS simulation L1011	February 26, 2011 13:53 by L1011	0	1,888
heaviside? ginette	February 25, 2011 15:24 by ginette	2	2,665

Read this first: How to ask a question on the forums

Page 181 of 242

181

	New posts		Hot thread with new posts
	No new posts		Hot thread with no new posts
	Thread is closed

Posting Rules
You may not post new threads You may not post replies You may not post attachments You may not edit your posts BB code is On Smilies are On [IMG] code is On HTML code is Off Forum Rules

All times are GMT -4. The time now is 12:45.