Hi everybody

I've got an error,can somebody help me?


/*---------------------------------------------------------------------------*\
| ========= | |
| \ / F ield | OpenFOAM: The Open Source CFD Toolbox |
| \ / O peration | Version: 1.4.1 |
| \ / A nd | Web: http://www.openfoam.org |
| \/ M anipulation | |
\*---------------------------------------------------------------------------*/

Exec : simpleFoam /home/gui/ essai2
Date : Oct 30 2007
Time : 11:24:50
Host : gui-desktop
PID : 9927
Root : /home/gui/
Case : essai2
Nprocs : 1
Create time

Create mesh for time = 0

Reading field p

Reading field U

Reading/calculating face flux field phi

Selecting incompressible transport model Newtonian
Selecting turbulence model kEpsilon

Starting time loop

Time = 0.1

DILUPBiCG: Solving for Ux, Initial residual = 1, Final residual = 0.027748, No Iterations 2
DILUPBiCG: Solving for Uy, Initial residual = 1, Final residual = 0.0273727, No Iterations 2
DILUPBiCG: Solving for Uz, Initial residual = 1, Final residual = 0.027986, No Iterations 2
#0 Foam::error::printStack(Foam:stream&) in "/home/gui/OpenFOAM/OpenFOAM-1.4.1/lib/linuxGccDPOpt/libOpenFOAM.so"
#1 Foam::sigFpe::sigFpeHandler(int) in "/home/gui/OpenFOAM/OpenFOAM-1.4.1/lib/linuxGccDPOpt/libOpenFOAM.so"
#2 Uninterpreted: [0xffffe420]
#3 void Foam::fvc::surfaceIntegrate<double>(Foam::Field<do uble>&, Foam::GeometricField<double,> const&) in "/home/gui/OpenFOAM/OpenFOAM-1.4.1/applications/bin/linuxGccDPOpt/simpleFoam"
#4 Foam::tmp<foam::geometricfield<double,> > Foam::fvc::surfaceIntegrate<double>(Foam::Geometri cField<double,> const&) in "/home/gui/OpenFOAM/OpenFOAM-1.4.1/applications/bin/linuxGccDPOpt/simpleFoam"
#5 Foam::tmp<foam::geometricfield<double,> > Foam::fvc::div<double>(Foam::GeometricField<double ,> const&) in "/home/gui/OpenFOAM/OpenFOAM-1.4.1/applications/bin/linuxGccDPOpt/simpleFoam"
#6 Foam::fv::gaussLaplacianScheme<double>::fvmLaplaci an(Foam::GeometricField<double ,> const&, Foam::GeometricField<double,>&) in "/home/gui/OpenFOAM/OpenFOAM-1.4.1/lib/linuxGccDPOpt/libfiniteVolume.so"
#7 Foam::fv::laplacianScheme<double>::fvmLaplacian(Fo am::GeometricField<double,> const&, Foam::GeometricField<double,>&) in "/home/gui/OpenFOAM/OpenFOAM-1.4.1/lib/linuxGccDPOpt/libfiniteVolume.so"
#8 Foam::tmp<foam::fvmatrix<double> > Foam::fvm::laplacian<double>(Foam::GeometricField< double,> const&, Foam::GeometricField<double,>&, Foam::word const&) in "/home/gui/OpenFOAM/OpenFOAM-1.4.1/applications/bin/linuxGccDPOpt/simpleFoam"
#9 Foam::tmp<foam::fvmatrix<double> > Foam::fvm::laplacian<double>(Foam::GeometricField< double,> const&, Foam::GeometricField<double,>&) in "/home/gui/OpenFOAM/OpenFOAM-1.4.1/applications/bin/linuxGccDPOpt/simpleFoam"
#10 Foam::tmp<foam::fvmatrix<double> > Foam::fvm::laplacian<double>(Foam::tmp<foam::geome tricfield<double,> > const&, Foam::GeometricField<double,>&) in "/home/gui/OpenFOAM/OpenFOAM-1.4.1/applications/bin/linuxGccDPOpt/simpleFoam"
#11 main in "/home/gui/OpenFOAM/OpenFOAM-1.4.1/applications/bin/linuxGccDPOpt/simpleFoam"
#12 __libc_start_main in "/lib/tls/i686/cmov/libc.so.6"
#13 Foam::regIOobject::readIfModified() in "/home/gui/OpenFOAM/OpenFOAM-1.4.1/applications/bin/linuxGccDPOpt/simpleFoam"
Exception en point flottant (core dumped)


Best regards

i have change the pressure and now i 've got

Create mesh for time = 0

Reading field p

Reading field U

Reading/calculating face flux field phi

Selecting incompressible transport model Newtonian
Selecting turbulence model kEpsilon

Starting time loop

Time = 0.1

GAMG: Solving for Ux, Initial residual = 1, Final residual = 0.025826, No Iterations 1
GAMG: Solving for Uy, Initial residual = 1, Final residual = 0.0253025, No Iterations 1
GAMG: Solving for Uz, Initial residual = 1, Final residual = 0.0478088, No Iterations 1
GAMG: Solving for p, Initial residual = 1, Final residual = 0.0498682, No Iterations 3
time step continuity errors : sum local = 3.8636, global = 1.01475, cumulative = 1.01475
#0 Foam::error::printStack(Foam:stream&) in "/home/gui/OpenFOAM/OpenFOAM-1.4.1/lib/linuxGccSPOpt/libOpenFOAM.so"
#1 Foam::sigFpe::sigFpeHandler(int) in "/home/gui/OpenFOAM/OpenFOAM-1.4.1/lib/linuxGccSPOpt/libOpenFOAM.so"
#2 Uninterpreted: [0xffffe420]
#3 Foam::tmp<foam::geometricfield<float,> > Foam::magSqr<foam::symmtensor<float>, Foam::fvPatchField, Foam::volMesh>(Foam::tmp<foam::geometricfield<foam ::symmtensor<float>, Foam::fvPatchField, Foam::volMesh> > const&) in "/home/gui/OpenFOAM/OpenFOAM-1.4.1/lib/linuxGccSPOpt/libincompressibleTurbulence Models.so"
#4 Foam::turbulenceModels::kEpsilon::correct() in "/home/gui/OpenFOAM/OpenFOAM-1.4.1/lib/linuxGccSPOpt/libincompressibleTurbulence Models.so"
#5 main in "/home/gui/OpenFOAM/OpenFOAM-1.4.1/applications/bin/linuxGccSPOpt/simpleFoam"
#6 __libc_start_main in "/lib/tls/i686/cmov/libc.so.6"
#7 Foam::regIOobject::readIfModified() in "/home/gui/OpenFOAM/OpenFOAM-1.4.1/applications/bin/linuxGccSPOpt/simpleFoam"
Exception en point flottant (core dumped)

somebody can help me?

regards

[hjasak]

You have messed up your boundary conditions on the pressure and ve;ocity and the solver is blowing up on you. If you specify p on the boundary, you cannot specify U.

Just to make sure, run checkMesh on your case - if this does not report any errors, you need to look into 0/p and 0/U - that's where the problem is.

A bit unusual choice of momentum solver - why?

Hrv

[alimansouri]

Hi there

I got the same error, I am ruuning simpleFoam and I checked most of the points mentioned on the board but still I get the following...pls help.

/*---------------------------------------------------------------------------*\
| ========= | |
| \ / F ield | OpenFOAM: The Open Source CFD Toolbox |
| \ / O peration | Version: 1.4.1 |
| \ / A nd | Web: http://www.openfoam.org |
| \/ M anipulation | |
\*---------------------------------------------------------------------------*/

Exec : simpleFoam /home/openfoam2/OpenFOAM/openfoam2-1.4.1/run/tutorials/simpleFoam elbow
Date : Jan 13 2009
Time : 11:42:37
Host : spidy3123.cluster.novachem.com
PID : 17477
Root : /home/openfoam2/OpenFOAM/openfoam2-1.4.1/run/tutorials/simpleFoam
Case : elbow
Nprocs : 1
Create time

Create mesh for time = 0

Reading field p

Reading field U

Reading/calculating face flux field phi

Selecting incompressible transport model Newtonian
Selecting turbulence model kEpsilon

Starting time loop

Time = 1

DILUPBiCG: Solving for Ux, Initial residual = 0.11164, Final residual = 0.00421292, No Iterations 3
DILUPBiCG: Solving for Uy, Initial residual = 0.0522537, Final residual = 0.000490851, No Iterations 3
DICPCG: Solving for p, Initial residual = 1, Final residual = 0.00992171, No Iterations 63
time step continuity errors : sum local = 0.0017069, global = -2.55781e-05, cumulative = -2.55781e-05
#0 Foam::error::printStack(Foam:stream&) in "/usr/local/OpenFOAM/OpenFOAM-1.4.1/lib/linuxGccDPOpt/libOpenFOAM.so"
#1 Foam::sigFpe::sigFpeHandler(int) in "/usr/local/OpenFOAM/OpenFOAM-1.4.1/lib/linuxGccDPOpt/libOpenFOAM.so"
#2 __restore in "/lib/tls/libpthread.so.0"
#3 Foam::divide(Foam::Field<double>&, Foam::UList<double> const&, Foam::UList<double> const&) in "/usr/local/OpenFOAM/OpenFOAM-1.4.1/lib/linuxGccDPOpt/libOpenFOAM.so"
#4 void Foam::divide<foam::fvpatchfield,>(Foam::GeometricF ield<double,>&, Foam::GeometricField<double,> const&, Foam::GeometricField<double,> const&) in "/usr/local/OpenFOAM/OpenFOAM-1.4.1/lib/linuxGccDPOpt/libincompressibleTurbulenc eModels.so"
#5 Foam::tmp<foam::geometricfield<double,> > Foam::operator/<foam::fvpatchfield,>(Foam::tmp<foam::geometricfie ld<double,> > const&, Foam::GeometricField<double,> const&) in "/usr/local/OpenFOAM/OpenFOAM-1.4.1/lib/linuxGccDPOpt/libincompressibleTurbulenc eModels.so"
#6 Foam::turbulenceModels::kEpsilon::correct() in "/usr/local/OpenFOAM/OpenFOAM-1.4.1/lib/linuxGccDPOpt/libincompressibleTurbulenc eModels.so"
#7 main in "/usr/local/OpenFOAM/OpenFOAM-1.4.1/applications/bin/linuxGccDPOpt/simpleFoam"
#8 __libc_start_main in "/lib/tls/libc.so.6"
#9 Foam::regIOobject::readIfModified() in "/usr/local/OpenFOAM/OpenFOAM-1.4.1/applications/bin/linuxGccDPOpt/simpleFoam"

[gschaider]

I'm betting on the old "k or epsilon is 0 (either internally or on some patch)"-bug

[lth]

Hello,
I am new to OpenFoam and am trying to test run a working solver for a new blockMeshdict file. I am learning as fast as possible to make my way around openFoam, but not sure where to go for debug help so specific. Any advice would be appreciated.

--Lori
-----------------------message-----

DILUPBiCG: Solving for StressTensor_2zz, Initial residual = 0, Final residual = 0, No Iterations 0
#0 Foam::error::printStack(Foam:stream&) in "/home/pec/OpenFOAM/OpenFOAM-1.5/lib/linuxGccDPOpt/libOpenFOAM.so"
#1 Foam::sigSegv::sigSegvHandler(int) in "/home/pec/OpenFOAM/OpenFOAM-1.5/lib/linuxGccDPOpt/libOpenFOAM.so"
#2 Uninterpreted: [0xb7fe0400]
#3 main in "/home/pec/OpenFOAM/OpenFOAM-1.5/applications/bin/linuxGccDPOpt/laminarPTTMultim od"
#4 __libc_start_main in "/lib/tls/i686/cmov/libc.so.6"
#5 _start in "/home/pec/OpenFOAM/OpenFOAM-1.5/applications/bin/linuxGccDPOpt/laminarPTTMultim od"
Segmentation fault