Getting a Wigley hull resistance case to run in OF 10

ibe · November 22, 2022, 16:11

Hi,

I'm trying to learn how to use Openfoam i.o.t. calculate small boat wave resistance.

As far as I can tell the earlier Wigley hull cases were developed with older versions of OF (e.g. http://www.wolfdynamics.com/tutorials.html?id=149)

I'm getting a variety of errors when I try to run that case (e.g.fieldMinMax unknown function )

Before I chase down these errors (and fixes), can folks recommend
what the best approach for a small boat wave resistance tool should be ? For example , an older version of OF that matches the use cases or a newer use case that runs with OF 10 (that I can't find) ?

Yann · November 23, 2022, 04:37

Hi,

There are hull cases in the tutorials of pretty much any OpenFOAM version. I don't know what version you are using but have a look into $FOAM_TUTORIALS/multiphase/interFoam

If you go for validation cases found online, my best advice would be to run the case on the same OpenFOAM version it has been developed for. For sure you can adjust the case setup to your current OpenFOAM version but if you are learning how to use OpenFOAM you are going to struggle a lot to adapt it. It's better to start with a working case and learn how it works before trying to modify things.

The headers of the Wolfdynamics case seems to indicate it was setup for OpenFOAM-6.

Have fun!
Yann

November 22, 2022, 16:11	Getting a Wigley hull resistance case to run in OF 10	#1
ibe New Member Join Date: Oct 2022 Posts: 11 Rep Power: 4	Hi, I'm trying to learn how to use Openfoam i.o.t. calculate small boat wave resistance. As far as I can tell the earlier Wigley hull cases were developed with older versions of OF (e.g. http://www.wolfdynamics.com/tutorials.html?id=149) I'm getting a variety of errors when I try to run that case (e.g.fieldMinMax unknown function ) Before I chase down these errors (and fixes), can folks recommend what the best approach for a small boat wave resistance tool should be ? For example , an older version of OF that matches the use cases or a newer use case that runs with OF 10 (that I can't find) ?

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Ability to run an openFOAM case at specific time	Dikkeunit	OpenFOAM Running, Solving & CFD	1	October 10, 2024 05:13
2DOF Planning hull resistance study with overset	CFD_fan	OpenFOAM Running, Solving & CFD	7	July 13, 2021 06:03
error while performing setField in wigley hull case	vava10	OpenFOAM Pre-Processing	3	September 25, 2020 10:17
Resistance calculation for flow around a ship hull	manoj_nav	OpenFOAM Running, Solving & CFD	0	December 17, 2015 02:03
Timestep in Free Surface Wigley Hull	Carlos Andrés	CFX	8	April 29, 2007 17:38

November 23, 2022, 04:37		#2
Yann Senior Member Yann Join Date: Apr 2012 Location: France Posts: 1,198 Rep Power: 27	Hi, There are hull cases in the tutorials of pretty much any OpenFOAM version. I don't know what version you are using but have a look into $FOAM_TUTORIALS/multiphase/interFoam If you go for validation cases found online, my best advice would be to run the case on the same OpenFOAM version it has been developed for. For sure you can adjust the case setup to your current OpenFOAM version but if you are learning how to use OpenFOAM you are going to struggle a lot to adapt it. It's better to start with a working case and learn how it works before trying to modify things. The headers of the Wolfdynamics case seems to indicate it was setup for OpenFOAM-6. Have fun! Yann