running a case of multiphase Nozzle 2d

harsha_kulkarni · June 19, 2014, 04:51

Hello friends,

I want to run a case whose location is given bellow.

/tutorials/multiphase/interFoam/les/nozzleFlow2D .

I want to see the geometry of this case but when I run the bockMesh command it gives following error

Inconsistency detected by ld.so: dl-version.c: 224: _dl_check_map_versions: Assertion `needed != ((void *)0)' failed!

plz help me

Thanks and regards
Harshawardhan K

Tushar@cfd · June 19, 2014, 05:06

Which linux version you are using?

Are you able to run other tutorials without errors?

harsha_kulkarni · June 19, 2014, 05:10

other's are also not running
ubuntu 13.10

Tushar@cfd · June 19, 2014, 05:29

Did you install the mentioned libraries on OF?

(1)

Code:

sudo apt-get install build-essential flex bison cmake zlib1g-dev qt4-dev-tools libqt4-dev gnuplot libreadline-dev libncurses-dev libxt-dev

(2)

Code:

sudo apt-get install libscotch-dev libopenmpi-dev

If not, then first update these.

If you have already done with the above installation then edit the following line of the "./bashrc" file in the $OF/etc/ directory:

WM_MPLIB=SYSTEMOPENMPI instead of WM_MPLIB=OPENMPI

Then close your terminal and rerun your case file.

June 19, 2014, 04:51	running a case of multiphase Nozzle 2d	#1
harsha_kulkarni Senior Member harshawardhank Join Date: Mar 2014 Posts: 209 Rep Power: 13	Hello friends, I want to run a case whose location is given bellow. /tutorials/multiphase/interFoam/les/nozzleFlow2D . I want to see the geometry of this case but when I run the bockMesh command it gives following error Inconsistency detected by ld.so: dl-version.c: 224: _dl_check_map_versions: Assertion `needed != ((void *)0)' failed! plz help me Thanks and regards Harshawardhan K

June 19, 2014, 05:29		#4
Tushar@cfd Senior Member T. Chourushi Join Date: Jul 2009 Posts: 321 Blog Entries: 1 Rep Power: 18	Did you install the mentioned libraries on OF? (1) Code: sudo apt-get install build-essential flex bison cmake zlib1g-dev qt4-dev-tools libqt4-dev gnuplot libreadline-dev libncurses-dev libxt-dev (2) Code: sudo apt-get install libscotch-dev libopenmpi-dev If not, then first update these. If you have already done with the above installation then edit the following line of the "./bashrc" file in the $OF/etc/ directory: WM_MPLIB=SYSTEMOPENMPI instead of WM_MPLIB=OPENMPI Then close your terminal and rerun your case file. Last edited by wyldckat; June 21, 2014 at 16:46. Reason: fixed broken code, which was incorrectly in URL mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Parallel running of 3D multiphase turbulence model (unknown problem!!)	MOHAMMAD67	OpenFOAM Running, Solving & CFD	7	November 23, 2015 11:53
interFoam running blowing up	sandy13	OpenFOAM Running, Solving & CFD	2	May 5, 2015 08:16
Running potentialFoam case with Gambit meshing	shuoxue	OpenFOAM Running, Solving & CFD	0	June 14, 2013 01:58
Running bubbleFoam for turbulent case...	vishal3	OpenFOAM	7	March 12, 2013 07:13
Setting up a turbine nozzle case	cfdengineer	CFX	2	August 2, 2010 06:49

June 19, 2014, 05:06		#2
Tushar@cfd Senior Member T. Chourushi Join Date: Jul 2009 Posts: 321 Blog Entries: 1 Rep Power: 18	Which linux version you are using? Are you able to run other tutorials without errors?

June 19, 2014, 05:10		#3
harsha_kulkarni Senior Member harshawardhank Join Date: Mar 2014 Posts: 209 Rep Power: 13	other's are also not running ubuntu 13.10