gradually openning the side wall of a tube to a environment with constant stagnations

immortality · November 17, 2012, 16:38

hello all my friends all over the world
I want to simulate a long channel you may assume closed end at right side but at the left side the wall move from rest at a constant velocity downward so that it opens to a constant stagnation pressure and stagnation temperature-that we know the values of them-environment that are greater than inside the channel.how can I model this gradually openning wall? should I mix groovyBC and mixed boundary conditions?how?or this can be done easier?
Thank you much for your helping.

immortality · November 18, 2012, 13:17

could anyone guide me about this problem?what should I do?the problem is 2-D and as I told moving wall BC is replaced with p0 and T0 BC at inlet gradually according to wall velocity.silmply saying its a gradually opennin of a wall to an environment.I appreciate any suggestion and guidance.can this be done by groovyBC?
is it necessary to assign different BC for each cell in boundary?
thank you.

immortality · November 20, 2012, 03:02

hello friends
I could simulate gradually opening the door with constant velocity at environment.now for replacing BC by stagnation properties I need the center values of cells neighbouring the boundary.how I can get and use of them?what are the needed functions?
Thank you

immortality · June 16, 2013, 13:09

Hi again
I managed to do it.if someone wanted my guidance I'm ready to help him/her.

November 17, 2012, 16:38	gradually openning the side wall of a tube to a environment with constant stagnations	#1
immortality Senior Member Ehsan Join Date: Oct 2012 Location: Iran Posts: 2,208 Rep Power: 27	hello all my friends all over the world I want to simulate a long channel you may assume closed end at right side but at the left side the wall move from rest at a constant velocity downward so that it opens to a constant stagnation pressure and stagnation temperature-that we know the values of them-environment that are greater than inside the channel.how can I model this gradually openning wall? should I mix groovyBC and mixed boundary conditions?how?or this can be done easier? Thank you much for your helping.

November 18, 2012, 13:17	any suggest?	#2
immortality Senior Member Ehsan Join Date: Oct 2012 Location: Iran Posts: 2,208 Rep Power: 27	could anyone guide me about this problem?what should I do?the problem is 2-D and as I told moving wall BC is replaced with p0 and T0 BC at inlet gradually according to wall velocity.silmply saying its a gradually opennin of a wall to an environment.I appreciate any suggestion and guidance.can this be done by groovyBC? is it necessary to assign different BC for each cell in boundary? thank you.

November 20, 2012, 03:02	solving the problem	#3
immortality Senior Member Ehsan Join Date: Oct 2012 Location: Iran Posts: 2,208 Rep Power: 27	hello friends I could simulate gradually opening the door with constant velocity at environment.now for replacing BC by stagnation properties I need the center values of cells neighbouring the boundary.how I can get and use of them?what are the needed functions? Thank you

June 16, 2013, 13:09		#4
immortality Senior Member Ehsan Join Date: Oct 2012 Location: Iran Posts: 2,208 Rep Power: 27	Hi again I managed to do it.if someone wanted my guidance I'm ready to help him/her. __________________ Injustice Anywhere is a Threat for Justice Everywhere.Martin Luther King. To Be or Not To Be,Thats the Question! The Only Stupid Question Is the One that Goes Unasked.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Wind turbine simulation	Saturn	CFX	60	July 17, 2024 06:45
Concentric tube heat exchanger (Air-Water)	Young	CFX	5	October 7, 2008 00:17
[blockMesh] BlockMeshmergePatchPairs	hjasak	OpenFOAM Meshing & Mesh Conversion	11	August 15, 2008 08:36
CFX Solver Memory Error	mike	CFX	1	March 19, 2008 08:22
[Commercial meshers] Converting meshes that includes interfaces	ham	OpenFOAM Meshing & Mesh Conversion	29	January 8, 2007 09:58