[Netgen] Importing mesh for complex 2D cases

edvardsenpriv · December 5, 2005, 18:12

As I understand OpenFOAM solves cases in 3 dimensions by default, but can be instructed to solve in 2 dimensions by specifying the "empty" boundary condition on boundaries normal to the (3rd) dimension. When using Netgen the only elements that seem to be possible to convert is tet-elements, for which the "empty" boundary condition can not be used (I assume). I had an idea that it maybe was possible to import a surface-mesh, which then could be extruded, but haven't succeded so far. Anyone has good experience in running 2D cases on imported automesh (netgen / other meshers)? sometimes even a 2D geometry gets complex...

Lars

eugene · December 6, 2005, 05:07

If you have a 2D surface and want to make a 2D mesh, you want to use extrudeMesh followed by autoPatch. Of course, tetrahedral elements cannot form a 2D mesh.

edvardsenpriv · December 6, 2005, 06:23

Thanks,
but are you able to import any 2D surface to OpenFOAM (from which mesher?), or do you use blockmesh? I have mainly used Netgen (which can also mesh 2D surface mesh), but in the netgenNeutralToFoam converter, 2D surface seems not yet to be supported.

Lars

December 5, 2005, 18:12	Importing mesh for complex 2D cases	#1
edvardsenpriv New Member Lars Edvarsen Join Date: Mar 2009 Posts: 14 Rep Power: 17	As I understand OpenFOAM solves cases in 3 dimensions by default, but can be instructed to solve in 2 dimensions by specifying the "empty" boundary condition on boundaries normal to the (3rd) dimension. When using Netgen the only elements that seem to be possible to convert is tet-elements, for which the "empty" boundary condition can not be used (I assume). I had an idea that it maybe was possible to import a surface-mesh, which then could be extruded, but haven't succeded so far. Anyone has good experience in running 2D cases on imported automesh (netgen / other meshers)? sometimes even a 2D geometry gets complex... Lars

December 6, 2005, 05:07	If you have a 2D surface and w	#2
eugene Senior Member Eugene de Villiers Join Date: Mar 2009 Posts: 725 Rep Power: 21	If you have a 2D surface and want to make a 2D mesh, you want to use extrudeMesh followed by autoPatch. Of course, tetrahedral elements cannot form a 2D mesh.

December 6, 2005, 06:23	Thanks, but are you able to i	#3
edvardsenpriv New Member Lars Edvarsen Join Date: Mar 2009 Posts: 14 Rep Power: 17	Thanks, but are you able to import any 2D surface to OpenFOAM (from which mesher?), or do you use blockmesh? I have mainly used Netgen (which can also mesh 2D surface mesh), but in the netgenNeutralToFoam converter, 2D surface seems not yet to be supported. Lars

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[snappyHexMesh] Creating multiple multiple cell zones with snappyHexMesh - a newbie in deep water!	divergence	OpenFOAM Meshing & Mesh Conversion	0	January 23, 2019 05:17
Gambit problems	Althea	FLUENT	22	January 4, 2017 04:19
[snappyHexMesh] SnappyHexMesh no layers and no decent mesh for complex geometry	pizzaspinate	OpenFOAM Meshing & Mesh Conversion	1	February 25, 2015 08:05
[Other] Importing 3D mesh from ANSYS to OpenFOAM	martyn88	OpenFOAM Meshing & Mesh Conversion	0	September 3, 2012 20:12
[Gmsh] 2D Mesh Generation Tutorial for GMSH	aeroslacker	OpenFOAM Meshing & Mesh Conversion	12	January 19, 2012 04:52