[mesh manipulation] Duplicate point found in cut face - stitchMesh - problem

RugbyGandalf · December 10, 2012, 05:54

Dear Foam-Community,

i am facing the following error, using stitchMesh:

"Duplicate point found in cut face. Error in the face cutting algorithm for global face 4(1199 ...)"

I generated a mesh, using blockMesh, consisting of three regions. Therefore duplicated points are necessary, to define those regions through different blocks (same with the accompanying patches). There are two meshes, i need to merge and stitch. To stitch them, I used the "createPatch"-tool, to form one inlet- and outlet-patch from three (caused by three regions).
Merging is fine, stitching produces the mentioned error.

Does anyone have an idea, how to solve this problem?

Regards,

Martin

ignacio · May 15, 2013, 06:23

Hello Martin,

I have the same problem. Three regions and the error message of Duplicate points when I try to stitch the faces.
Did you find out how to solve it?

Thanks,

Ignacio

Ankit.Dave · March 9, 2017, 01:16

Hello Martin and Ignacio,

I am facing the same problem. Have you resolved it?

behrouz_Beh · April 23, 2018, 21:27

I know this is an old thread but for future use, I mention my experience for this error.
I had the same error with my blockMesh. In my case, I did not define the edges well . After well defining the edges ( for circle in geometry) the problem was solved.

Hope it helps.

cfd_user_pune · September 8, 2019, 04:43

Quote:

Originally Posted by behrouz_Beh

I know this is an old thread but for future use, I mention my experience for this error.
I had the same error with my blockMesh. In my case, I did not define the edges well . After well defining the edges ( for circle in geometry) the problem was solved.

Hope it helps.

I am using SALOME 8.2 for meshing Mixing Tank geometry (stator and rotor). What do you mean by 'defining edge well'. How do i follow same in salome? Do i need to extract edges in my mesh with salome?

brammekeuh987 · April 2, 2020, 15:45

Hi

Over here: stitchMesh : duplicate point

Try the "-perfect" option when the mesh fits perfectly.

Hope it helps!

December 10, 2012, 05:54	Duplicate point found in cut face - stitchMesh - problem	#1
RugbyGandalf Member Martin Join Date: Aug 2010 Location: Germany Posts: 55 Rep Power: 16	Dear Foam-Community, i am facing the following error, using stitchMesh: "Duplicate point found in cut face. Error in the face cutting algorithm for global face 4(1199 ...)" I generated a mesh, using blockMesh, consisting of three regions. Therefore duplicated points are necessary, to define those regions through different blocks (same with the accompanying patches). There are two meshes, i need to merge and stitch. To stitch them, I used the "createPatch"-tool, to form one inlet- and outlet-patch from three (caused by three regions). Merging is fine, stitching produces the mentioned error. Does anyone have an idea, how to solve this problem? Regards, Martin

March 9, 2017, 01:16	Duplicate point found in cut face.	#3
Ankit.Dave New Member Ankit Dave Join Date: Aug 2016 Location: India Posts: 11 Rep Power: 10	Hello Martin and Ignacio, I am facing the same problem. Have you resolved it?

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[blockMesh] Internal walls of zero thickness	anger	OpenFOAM Meshing & Mesh Conversion	23	February 6, 2020 19:25
8x icoFoam speed up with Cufflink CUDA solver library	kmooney	OpenFOAM Running, Solving & CFD	42	November 6, 2012 12:37
[blockMesh] error EOF in blockMesh	Ahmed Khattab	OpenFOAM Meshing & Mesh Conversion	7	May 17, 2012 01:37
[blockMesh] BlockMeshmergePatchPairs	hjasak	OpenFOAM Meshing & Mesh Conversion	11	August 15, 2008 08:36
[Gmsh] Gmsh and samplesurface	touf	OpenFOAM Meshing & Mesh Conversion	2	December 10, 2007 03:27

May 15, 2013, 06:23		#2
ignacio Member Ignacio Join Date: Jan 2013 Posts: 33 Rep Power: 13	Hello Martin, I have the same problem. Three regions and the error message of Duplicate points when I try to stitch the faces. Did you find out how to solve it? Thanks, Ignacio

April 23, 2018, 21:27		#4
behrouz_Beh New Member Join Date: Aug 2017 Posts: 2 Rep Power: 0	I know this is an old thread but for future use, I mention my experience for this error. I had the same error with my blockMesh. In my case, I did not define the edges well . After well defining the edges ( for circle in geometry) the problem was solved. Hope it helps.

April 2, 2020, 15:45		#6
brammekeuh987 Member Bram Kerkhofs1 Join Date: Oct 2016 Posts: 30 Rep Power: 10	Hi Over here: stitchMesh : duplicate point Try the "-perfect" option when the mesh fits perfectly. Hope it helps!