[OpenFOAM.org] Installation of OpenFOAM on Mac: STLsurfaceFormatASCII.o error?

APCoding · October 17, 2016, 23:12

Hi!

It seemed as if everything was working fine with my installation, but when I tried to run icoFoam or blockMesh, it said the command wasn't found. I saw this on the OpenFOAM wiki, but it pretty much said find the error and look online. If I selected the right error (it was the only line with "Error ", which is what the wiki wanted me to look for), it seems to have a problem with the

Code:

STLsurfaceFormatASCII.o

file. What's wrong? What did I miss? I can post the other 20 error messages if this doesn't mean anything. Thanks for all your help! Here's the full error:

Code:

make: *** [/Users/PeterE/OpenFOAM/OpenFOAM-4.0/platforms/darwin64ClangDPInt32Opt/src/surfMesh/surfaceFormats/stl/STLsurfaceFormatASCII.o] Error 1

I'm trying to install OpenFOAM 4.0 on macOS Sierra.

wyldckat · October 30, 2016, 12:52

Quick questions:

What were the error lines that appeared before that?
- If in doubt which lines you should be looking for, please run the following command:
  Code:
```
gzip < log.make > log.make.gz
```
  And attached the file "log.make.gz" to your next post.
Which installation instructions are you following?

October 17, 2016, 23:12	Installation of OpenFOAM on Mac: STLsurfaceFormatASCII.o error?	#1
APCoding New Member Peter Join Date: Sep 2016 Posts: 13 Rep Power: 10	Hi! It seemed as if everything was working fine with my installation, but when I tried to run icoFoam or blockMesh, it said the command wasn't found. I saw this on the OpenFOAM wiki, but it pretty much said find the error and look online. If I selected the right error (it was the only line with "Error ", which is what the wiki wanted me to look for), it seems to have a problem with the Code: STLsurfaceFormatASCII.o file. What's wrong? What did I miss? I can post the other 20 error messages if this doesn't mean anything. Thanks for all your help! Here's the full error: Code: make: *** [/Users/PeterE/OpenFOAM/OpenFOAM-4.0/platforms/darwin64ClangDPInt32Opt/src/surfMesh/surfaceFormats/stl/STLsurfaceFormatASCII.o] Error 1 I'm trying to install OpenFOAM 4.0 on macOS Sierra.

October 30, 2016, 12:52		#2
wyldckat Retired Super Moderator Bruno Santos Join Date: Mar 2009 Location: Lisbon, Portugal Posts: 10,982 Blog Entries: 45 Rep Power: 128	Quick questions: What were the error lines that appeared before that? If in doubt which lines you should be looking for, please run the following command: Code: gzip < log.make > log.make.gz And attached the file "log.make.gz" to your next post. Which installation instructions are you following? __________________ OpenFOAM: FAQ \| Getting started Forum: How to get help, to post code/output and forum guide Read this before sending me PM

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Compile calcMassFlowC	aurore	OpenFOAM Programming & Development	13	March 23, 2018 08:43
Mesquite - Adaptive mesh refinement / coarsening?	philippose	OpenFOAM Running, Solving & CFD	94	January 27, 2016 10:40
[swak4Foam] installing funkySetFields	igo	OpenFOAM Community Contributions	1	November 20, 2012 21:16
Installation OF1.5-dev	ttdtud	OpenFOAM Installation	46	May 5, 2009 03:32
How to get the max value of the whole field	waynezw0618	OpenFOAM Running, Solving & CFD	4	June 17, 2008 06:07