|
[Sponsors] |
SurfaceWriters other than raw are not selectable in sampleSurface |
![]() |
|
LinkBack | Thread Tools | Search this Thread | Display Modes |
![]() |
![]() |
#1 |
Senior Member
Hannes Kröger
Join Date: Mar 2009
Location: Rostock, Germany
Posts: 124
Rep Power: 18 ![]() |
Description:
When other writers than "raw" (for example "vtk") are selected in the sampleSurfaceDict, the program stops and complains that "raw" is the only possible selection (i.e. it presents a list of possible writers, that only contains "raw"). The problem seems to be, that there are no vtk-, dx- and so on writers defined for the types "SphericalTensor" and "SymmTensor" When all parts concerning volSphericalTensorField and volSymmTensorField are commented out in sampleSurface.C, all works fine. Solver/Application: sampleSurface Source file: Testcase: Platform: Version: OpenFOAM-1.4 (also 1.4.1) Notes:
__________________
silentdynamics GmbH - http://silentdynamics.de open source CAE software solutions & support |
|
![]() |
![]() |
![]() |
![]() |
#2 |
Senior Member
Join Date: Mar 2009
Posts: 854
Rep Power: 22 ![]() |
Are you sure this doesn't work in 1.4.1, I implemented all the writers for all the field types in that version but I only performed basic testing.
|
|
![]() |
![]() |
![]() |
![]() |
#3 |
Senior Member
Hannes Kröger
Join Date: Mar 2009
Location: Rostock, Germany
Posts: 124
Rep Power: 18 ![]() |
Hello Henry,
I am still working with 1.4 but I tried to replace the sampleSurface-1.4 by the one from 1.4.1 and compiled that. Both versions behaved pretty much the same. But maybe I messed up something. I will check it again when I find some time and report again. Best regards, Hannes
__________________
silentdynamics GmbH - http://silentdynamics.de open source CAE software solutions & support |
|
![]() |
![]() |
![]() |
![]() |
#4 |
Senior Member
Join Date: Mar 2009
Posts: 854
Rep Power: 22 ![]() |
I just tested the version in 1.4.1 and it worked fine for me.
|
|
![]() |
![]() |
![]() |
![]() |
#5 |
Senior Member
Mark Olesen
Join Date: Mar 2009
Location: https://olesenm.github.io/
Posts: 1,714
Rep Power: 40 ![]() ![]() |
Hi Hannes,
If you are back-porting the utility to 1.4, be sure that you grab all the sub-directories too (especially surfaceWriters!). |
|
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
SampleSurface problem | saf5029 | OpenFOAM Post-Processing | 2 | June 13, 2008 14:42 |
[Gmsh] Gmsh and samplesurface | touf | OpenFOAM Meshing & Mesh Conversion | 2 | December 10, 2007 02:27 |
[OpenFOAM] Question about sampleSurface | osimonsimon | ParaView | 0 | October 16, 2006 22:32 |
[OpenFOAM] Zero values using sampleSurface | steja | ParaView | 2 | June 15, 2006 04:23 |
grid adaption mode NOT selectable via VNC | Ralf Schmidt | FLUENT | 2 | May 24, 2006 02:35 |