|
[Sponsors] |
October 10, 2001, 06:11 |
--Looking for free jet code--
|
#1 |
Guest
Posts: n/a
|
Hi, I want a free jet code like GENMIX. I have a successful code to calculate methane turbulent jet diffusion flame, but it is developed on the base of GENMIX which is too old, I think, so I want to know who or how I can get a similar source code to calculate axisymmetric gas jet flow using k-epcilon turbulent model with or without chemical reactions. provide me any information you know and give me a hand. Any help will be appreciated.
thanks. |
|
October 10, 2001, 13:30 |
Re: --Looking for free jet code--
|
#2 |
Guest
Posts: n/a
|
Without chemical reaction: try NPARC, Check this one:
http://www.grc.nasa.gov/www/wind/val.../axinoz01.html Note: K-e turbulence model will not be able to give you a good solution (round jet/plane jet anomaly). An explicit compressibility correction terms are needed to get a good approximation to the turbulent jet flow. Regards Danny |
|
October 11, 2001, 13:15 |
Re: --Looking for free jet code--
|
#3 |
Guest
Posts: n/a
|
Dear Danny,
I would be interested if there is a free source code. I am quite interested in the Spalart-Allmaras model and I think it will certainly save my time to implement the model if I can have an another code for reference, although the numerical results using SA model shown in that website did not match the experimental data very well. Best wishes Li Yang |
|
October 11, 2001, 14:28 |
Re: --Looking for free jet code--
|
#4 |
Guest
Posts: n/a
|
To Li Yang:
I think if you are US citizen or use NPARC/WIND in US, you can get it for free. Several one and two equation turbulence models are available for use with NPARC code Check Prof. Laney page: http://capella.colorado.edu/~laney/softaero.htm I myself use open source code developed by Los Alamos US Department of Energy (CFDLIB). http://capella.colorado.edu/~laney/softgen.htm It is NOT user friendly code but it is well written code and it gives you a lot of flexibility to control your calculation. Regards Danny Tan |
|
October 12, 2001, 05:53 |
Re: --Looking for free jet code--
|
#5 |
Guest
Posts: n/a
|
Dear Danny,
Thank you very much for the information you provided but I am afraid I am not a US citizen so I won't be able to get them for free. The code CFDLIB you are using sounds very interesting to me. I would like to know if CFDLIB is of parallel processing function (using MPI ?). I guess it is a non-staggered grid code and I wonder if it is suitable for LES. Your reply would be very much appreciated. Best wishes Li Yang |
|
October 12, 2001, 11:08 |
Re: --Looking for free jet code--
|
#6 |
Guest
Posts: n/a
|
Li Yang:
Yes, you can use CFDLIB in parallel processor. About Large Eddy Simulation, you better ask Dr. Kashiwa who is currently conducting research in turbulence modeling for CFDLIB. http://gnarly.lanl.gov/Cfdlib/Cfdlib.html Regards Danny Tan |
|
October 12, 2001, 15:15 |
Re: --Looking for free jet code--
|
#7 |
Guest
Posts: n/a
|
Thank you very much, Danny.
Regards Li Yang |
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Supersonic Jet Flows | Danny Tan | FLUENT | 0 | November 30, 2001 22:01 |
--looking for free jet source code--(again) | Haifeng Wang | Main CFD Forum | 1 | October 13, 2001 16:33 |
Design Integration with CFD? | John C. Chien | Main CFD Forum | 19 | May 17, 2001 16:56 |
What is the Better Way to Do CFD? | John C. Chien | Main CFD Forum | 54 | April 23, 2001 09:10 |
own Code vs. commercial code | Bernhard Mueck | Main CFD Forum | 10 | February 16, 2000 11:07 |