|
[Sponsors] |
![]() |
![]() |
#1 |
Guest
Posts: n/a
|
Hello everyone
I am trying to compile a udf. But when I load the file an error pop up. The system cannot find the file specified. (system "copy C:\Fluent.Inc\fluent6.3.26\src\makefile_nt.udf libudf\ntx86\2d\makefile") 1 file(s) copied. (chdir "libudf")() (chdir "ntx86\2d")() 'nmake' is not recognized as an internal or external command, operable program or batch file. 'nmake' is not recognized as an internal or external command, operable program or batch file. Opening library "libudf"... Error: open_udf_library: The system cannot find the file specified. Error Object: () How do I rectify this ? Thanks |
|
![]() |
![]() |
![]() |
#2 |
Guest
Posts: n/a
|
Dear Sid sure that your problem is about VS instalation. you certainly must reinstall VS , during instalation you face whit a option by this title: "register enviroment varible ". you must check it and go on instalation. Best Amir
|
|
![]() |
![]() |
![]() |
#3 |
Guest
Posts: n/a
|
If you have installed the Visual studio 2005, you can try..
Start->All programs->Microsoft visual studio 2005 ->Visual studio tools ->Visual Studio 2005 Command Prompt After the operation, you can see a DOS interface. Use DOS command to find your work fold, and then run fluent. (You directly input "fluent" after DOS prompt and click "return" key) Open your case and compile UDF. It should be OK. Good luck. |
|
![]() |
![]() |
![]() |
#4 |
Guest
Posts: n/a
|
Hi
We are also facing the same kind of problem during the compilation of UDF in Fluent. we installed Visual Studio 6 but we are not able to link it with FLUENT. As Braket mentioned the following procedure...to reply ur query so we tried to link Visual Studio..as mentionen by braket.. If you have installed the Visual studio 2005, you can try.. Start->All programs->Microsoft visual studio 2005 ->Visual studio tools ->Visual Studio 2005 Command Prompt After the operation, you can see a DOS interface. Use DOS command to find your work fold, and then run fluent. (You directly input "fluent" after DOS prompt and click "return" key) Open your case and compile UDF. but following the mentioned path......Start->All programs->Microsoft visual studio 2005 ->Visual studio tools ->Visual Studio 2005 Command Prompt we could not able to find the Visual Studio 2005 Command Prompt...nd could not use the dos to find the work fold. i.e. we icon we have to click after following the path... Start->All Programmes->Microsoft viual studio 2006->visual studio tools-> wht nxt???? pls specify step by step procedure to compile the UDF afer reaching this step. nd wht DOS commands are reqd. Start->All Programmes->Microsoft viual studio 2006->visual studio tools |
|
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Problem with UDF compiling for kTkLW model | Wantami | FLUENT | 0 | July 18, 2011 05:11 |
ParaView for OF-1.6-ext | Chrisi1984 | OpenFOAM Installation | 0 | December 31, 2010 06:42 |
Accessing phi from a fvPatchField at same patch | johndeas | OpenFOAM | 1 | September 13, 2010 20:23 |
Installation OF1.5-dev | ttdtud | OpenFOAM Installation | 46 | May 5, 2009 02:32 |
Problem with compile the setParabolicInlet | ivanyao | OpenFOAM Running, Solving & CFD | 6 | September 5, 2008 20:50 |