How can I break a fluent calculation?

enry · March 1, 2010, 06:10

Hi, I'm simulating an unsteady flow, and I impose some time steps to FLUENT "a priori"; however my goal is to break FLUENT calculation "a posteriori", under some bond.

So my idea is to to write a UDF that under some bond impose to FLUENT to break the calculation, even if I impose "a priori" the number of time steps, but FLUENT can't read the command "exit" in my UDF.
Can you help me?
Thanks in advance.

Robert@cfd · March 1, 2010, 11:28

Hi
Did you try the touch-command?

http://willem.engen.nl/uni/fluent/do...ips-Tricks.pdf
read page 9/10 for further informations

I didnt try it, but maybe it helps.

Greetings

enry · March 1, 2010, 11:51

Hi, thanks for your reply.
Maybe it can be useful.

gemini · March 5, 2010, 04:22

See section 3.7 Input/Output Macros in UDF manual. It might help...

good luck

enry · March 5, 2010, 05:17

Thanks!
enry

Robert@cfd · April 5, 2010, 20:18

Hi
Did you find a solution to the problem?

March 1, 2010, 06:10	How can I break a fluent calculation?	#1
enry Senior Member Herman Join Date: Nov 2009 Posts: 122 Rep Power: 17	Hi, I'm simulating an unsteady flow, and I impose some time steps to FLUENT "a priori"; however my goal is to break FLUENT calculation "a posteriori", under some bond. So my idea is to to write a UDF that under some bond impose to FLUENT to break the calculation, even if I impose "a priori" the number of time steps, but FLUENT can't read the command "exit" in my UDF. Can you help me? Thanks in advance.

March 1, 2010, 11:51		#3
enry Senior Member Herman Join Date: Nov 2009 Posts: 122 Rep Power: 17	Hi, thanks for your reply. Maybe it can be useful. Last edited by enry; March 17, 2010 at 10:10.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[Commercial meshers] Fluent3DMeshToFoam	simvun	OpenFOAM Meshing & Mesh Conversion	50	January 19, 2020 16:33
Two questions on Fluent UDF	Steven	Fluent UDF and Scheme Programming	7	March 23, 2018 04:22
power and pumping number calculation in "FLUENT"	HARI SANKAR	FLUENT	1	March 29, 2011 17:20
Fluent 12.0 is worst then Fluent 6.2	herntan	FLUENT	5	December 14, 2009 03:57
Fluent Cd calculation	liflu	FLUENT	0	October 31, 2009 11:03

March 1, 2010, 11:28		#2
Robert@cfd Member Robert Join Date: Feb 2010 Location: Germany Posts: 32 Rep Power: 16	Hi Did you try the touch-command? http://willem.engen.nl/uni/fluent/do...ips-Tricks.pdf read page 9/10 for further informations I didnt try it, but maybe it helps. Greetings

March 5, 2010, 04:22		#4
gemini Member Join Date: Mar 2009 Location: Istanbul, Turkiye Posts: 47 Rep Power: 17	See section 3.7 Input/Output Macros in UDF manual. It might help... good luck

March 5, 2010, 05:17		#5
enry Senior Member Herman Join Date: Nov 2009 Posts: 122 Rep Power: 17	Thanks! enry

April 5, 2010, 20:18		#6
Robert@cfd Member Robert Join Date: Feb 2010 Location: Germany Posts: 32 Rep Power: 16	Hi Did you find a solution to the problem?