define source term

behzzad93 · November 18, 2017, 08:33

hi everyone

i have a serious problem in fluent

what is the udf for permeate flux?...i have to modeling a tube that have an inlet and outlet, but the walls of tube have permeability. indeed i want to model a membrane that fluid enters the inlet and a little bit of fluid passes through the wall(i know the equation for permeability) and rejected fluid is exited from the outlet. so can anyone tell me how can i define a udf for this equation please?..i realized i have to use sink & source method for wall boundary condition, also i have to use "define_source" macro. but i didn't see examples for this section.
i don't know how to write udf for this boundary!!.

thank you

behzzad93 · November 18, 2017, 08:43

the equation of permeability is in attachment

zobekenobe · June 25, 2018, 12:24

Hey behzzad,

In case you are still figuring the solution, here is what I am doing.

I have defined the membrane as a velocity inlet and written a UDF and used DEFINE_PROFILE to specify the flux through the membrane (-ve in sign as it exits the boundary). The secondary phase could be set as zero to not allow it to flow through.

If you restrict the flow through the boundary, it begins to act a permeable surface. by using DEFINE_SOURCE you can account for the material that leaves the system and probably enters the other phase. for a UDS you would have to define your own else for species it is accounted for in the mass transfer definition.

November 18, 2017, 08:33	define source term	#1
behzzad93 New Member behzad Join Date: May 2017 Posts: 5 Rep Power: 9	hi everyone i have a serious problem in fluent what is the udf for permeate flux?...i have to modeling a tube that have an inlet and outlet, but the walls of tube have permeability. indeed i want to model a membrane that fluid enters the inlet and a little bit of fluid passes through the wall(i know the equation for permeability) and rejected fluid is exited from the outlet. so can anyone tell me how can i define a udf for this equation please?..i realized i have to use sink & source method for wall boundary condition, also i have to use "define_source" macro. but i didn't see examples for this section. i don't know how to write udf for this boundary!!. thank you

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[swak4Foam] swak4foam for OpenFOAM 4.0	mnikku	OpenFOAM Community Contributions	80	May 17, 2022 09:06
[foam-extend.org] Problems installing foam-extend-4.0 on openSUSE 42.2 and Ubuntu 16.04	ordinary	OpenFOAM Installation	19	September 3, 2019 19:13
what is swap4foam ??	AB08	OpenFOAM	28	February 2, 2016 02:22
OpenFOAM on MinGW crosscompiler hosted on Linux	allenzhao	OpenFOAM Installation	127	January 30, 2009 20:08
DecomposePar links against liblamso0 with OpenMPI	jens_klostermann	OpenFOAM Bugs	11	June 28, 2007 18:51

June 25, 2018, 12:24		#3
zobekenobe Member zobekenobe Join Date: Mar 2009 Location: Dublin, Ireland Posts: 72 Rep Power: 17	Hey behzzad, In case you are still figuring the solution, here is what I am doing. I have defined the membrane as a velocity inlet and written a UDF and used DEFINE_PROFILE to specify the flux through the membrane (-ve in sign as it exits the boundary). The secondary phase could be set as zero to not allow it to flow through. If you restrict the flow through the boundary, it begins to act a permeable surface. by using DEFINE_SOURCE you can account for the material that leaves the system and probably enters the other phase. for a UDS you would have to define your own else for species it is accounted for in the mass transfer definition.