Patch application in VOF model

Jing · July 31, 2013, 06:28

Hi everyone,

I have a problem when I use Patch in VOF and hope someone could clear my doubt!

The problem is as follow:

The model has two phases- one is oil and another is water. I hope to simulate the process of the two phases flowing a cylinder.
I initialized with water(primary phase), then checked the contours of volume fraction, and can see a whole pipe of water. Then I patched oil to the inner part of the pipe, hoping get an initialization of oil core surrounded with water. But after the patching, I checked the contours of volume fraction again. The contours didn't show an oil core surrounded with water, but whole section of oil.

I tried several times, still the same results. I wander does the contours indicate that the patching is not applied successfully or it does applied successfully but the contours don't update after the patching?

Kind Regards,

Jing

shikamaru · July 31, 2013, 07:12

Contours updates after patching. Something is wrong when you are patching for oil. How are you selecting the region? Region>mark?

Jing · July 31, 2013, 07:52

Hi Shikamaru,

Thanks for your reply! I found the problem now. I did use the Region>mark. But the mistake I made is that when I selected the Patch Region, I not only selected the register but also selected the Zones to patch, which made the whole piped patched with oil!

But if I adapt a cylinder region, and mark it, is it true that the registered cylinder region is not exact the same as what I defined. I found the marked cylinder is slimmer near inlet and outlet.

July 31, 2013, 06:28	Patch application in VOF model	#1
Jing New Member Jing Shi Join Date: Feb 2013 Posts: 20 Rep Power: 13	Hi everyone, I have a problem when I use Patch in VOF and hope someone could clear my doubt! The problem is as follow: The model has two phases- one is oil and another is water. I hope to simulate the process of the two phases flowing a cylinder. I initialized with water(primary phase), then checked the contours of volume fraction, and can see a whole pipe of water. Then I patched oil to the inner part of the pipe, hoping get an initialization of oil core surrounded with water. But after the patching, I checked the contours of volume fraction again. The contours didn't show an oil core surrounded with water, but whole section of oil. I tried several times, still the same results. I wander does the contours indicate that the patching is not applied successfully or it does applied successfully but the contours don't update after the patching? Kind Regards, Jing

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Problem with cyclic boundaries in Openfoam 1.5	fs82	OpenFOAM	37	November 29, 2024 11:15
AMI speed performance	danny123	OpenFOAM	21	October 24, 2020 05:13
[Commercial meshers] Mesh conversion problem (fluent3DMeshToFoam)	Aadhavan	OpenFOAM Meshing & Mesh Conversion	2	March 8, 2018 02:47
[GAMBIT] periodic faces not matching	Aadhavan	ANSYS Meshing & Geometry	6	August 31, 2013 12:25
UDF for ellipse shape volume patch in VOF model	nazeem	FLUENT	1	October 8, 2004 12:22

July 31, 2013, 07:12		#2
shikamaru New Member Nara Shikamaru Join Date: Apr 2012 Posts: 22 Rep Power: 14	Contours updates after patching. Something is wrong when you are patching for oil. How are you selecting the region? Region>mark?

July 31, 2013, 07:52		#3
Jing New Member Jing Shi Join Date: Feb 2013 Posts: 20 Rep Power: 13	Hi Shikamaru, Thanks for your reply! I found the problem now. I did use the Region>mark. But the mistake I made is that when I selected the Patch Region, I not only selected the register but also selected the Zones to patch, which made the whole piped patched with oil! But if I adapt a cylinder region, and mark it, is it true that the registered cylinder region is not exact the same as what I defined. I found the marked cylinder is slimmer near inlet and outlet.