Mesh geeration and user guide EnGrid

SimonStar · April 23, 2020, 04:39

Hello guys, I think I need your help.

I’m working with OpenFOAM and I want to try EnGrid. I have two questions about it

First:
Where to find good information how to use the program? I only found on tutorial on Youtube from Calum Douglas.
https://www.youtube.com/watch?v=VwSXldG3ank&t=315s

Second:
The tutorial sounds good for me but the programm just doesn’t do what he says. For example he says right at the beginning to press p to open a window but nithing happens on my own Computer. Do others/ you also have the same problem?

I ran it as an administrtor
I joined all parts to a single part
I saved it as binary .stl -file (ASCII-option deactivateted, so I think its binary)

The text on the right side of EnGrid says the following:

secs. for class IOOperation: 53
cleaning STL geometry:
tolerance = 1e-010
The STL geometry seems to be clean.
secs. for class CorrectSurfaceOrientation: 0
removing 'stray' nodes
deleting 0 nodes!
secs. for class DeleteStrayNodes: 0
marking non-manifold edges
done.
updating node information ...
done.
swapping edges for surface triangles ...
loop 1/1
sub-loop 1: 0 swaps
secs. for undefined: 0
updating node information ...
done.
secs. for class FixCadGeometry: 0
secs. for class IOOperation: 11
OnChar p
OnChar s --> This is doing nothing...

Any Ideas?
Thank you in advance!

Saurabh__ · June 11, 2021, 07:58

1- left click on surface (lets say on face )
2- press p (then red spot will seen in window)
3-press s then it will ask bc condition

above process you have do until and unless you haven't set all bc remember red spot imp

if not working please reply or try to install it again.

April 23, 2020, 04:39	Mesh geeration and user guide EnGrid	#1
SimonStar Member Simon Join Date: Sep 2019 Location: Germany Posts: 51 Rep Power: 7	Hello guys, I think I need your help. I’m working with OpenFOAM and I want to try EnGrid. I have two questions about it First: Where to find good information how to use the program? I only found on tutorial on Youtube from Calum Douglas. https://www.youtube.com/watch?v=VwSXldG3ank&t=315s Second: The tutorial sounds good for me but the programm just doesn’t do what he says. For example he says right at the beginning to press p to open a window but nithing happens on my own Computer. Do others/ you also have the same problem? I ran it as an administrtor I joined all parts to a single part I saved it as binary .stl -file (ASCII-option deactivateted, so I think its binary) The text on the right side of EnGrid says the following: secs. for class IOOperation: 53 cleaning STL geometry: tolerance = 1e-010 The STL geometry seems to be clean. secs. for class CorrectSurfaceOrientation: 0 removing 'stray' nodes deleting 0 nodes! secs. for class DeleteStrayNodes: 0 marking non-manifold edges done. updating node information ... done. swapping edges for surface triangles ... loop 1/1 sub-loop 1: 0 swaps secs. for undefined: 0 updating node information ... done. secs. for class FixCadGeometry: 0 secs. for class IOOperation: 11 OnChar p OnChar s --> This is doing nothing... Any Ideas? Thank you in advance! Last edited by SimonStar; April 24, 2020 at 10:15.

June 11, 2021, 07:58	sir it does work	#2
Saurabh__ New Member Saurabh Join Date: Jul 2019 Posts: 4 Rep Power: 7	1- left click on surface (lets say on face ) 2- press p (then red spot will seen in window) 3-press s then it will ask bc condition above process you have do until and unless you haven't set all bc remember red spot imp if not working please reply or try to install it again.