Events not visible on timing map

rmotwan · March 7, 2021, 01:59

Hello,

I'm working on an IC engine simulation and the cyclic valve events are not showing up in the timing map. Even keeping visibility ON for events only under Timing Map > Edit > Settings in Converge Studio doesn't show valve events on the timing map.

Does anyone know what could be the issue?

MFGT · March 8, 2021, 02:39

You can shift these (pink) cyclic events by their cyclic length with the mouse wheel, just select the right row and scroll.

Furthermore, either clicking "refresh" or "reset" should bring your cyclic events back on the timing map.

rmotwan · May 10, 2021, 20:24

Hi Tobias,

I tried the old uninstall and install Studio again but the problem persists. I can other entities on the timing map but not the events, even though I can see them in the case setup.

psrikanth · May 12, 2021, 20:10

Are these open/close events or valve type events? Another easy way to check if it is an issue with the Studio installation would probably be to open up an example case and see if you can see the cyclic events in the timing map.

rmotwan · May 12, 2021, 23:31

I'm talking specifically about the valve events. Even for the example cases, valve events are not visible, and if I select only Events in Timing Map > Edit, the map is blank.

March 7, 2021, 01:59	Events not visible on timing map	#1
rmotwan New Member Rahul Motwani Join Date: Feb 2021 Location: Greenville, SC Posts: 18 Rep Power: 5	Hello, I'm working on an IC engine simulation and the cyclic valve events are not showing up in the timing map. Even keeping visibility ON for events only under Timing Map > Edit > Settings in Converge Studio doesn't show valve events on the timing map. Does anyone know what could be the issue?

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[General] Extracting ParaView Data into Python Arrays	Jeffzda	ParaView	30	November 6, 2023 22:00
CFD post cannot load results-Error appeared?	mariam.sara	ANSYS	9	September 17, 2018 16:23
[mesh manipulation] Importing Multiple Meshes	thomasnwalshiii	OpenFOAM Meshing & Mesh Conversion	18	December 19, 2015 19:57
[OpenFOAM] could not open file .vtk in paraview	ali_atrian	ParaView	8	August 27, 2014 11:31
fluent add additional zones for the mesh file	SSL	FLUENT	2	January 26, 2008 12:55

March 8, 2021, 02:39		#2
MFGT Senior Member Tobias Join Date: May 2016 Location: Germany Posts: 295 Rep Power: 11	You can shift these (pink) cyclic events by their cyclic length with the mouse wheel, just select the right row and scroll. Furthermore, either clicking "refresh" or "reset" should bring your cyclic events back on the timing map.

May 10, 2021, 20:24		#3
rmotwan New Member Rahul Motwani Join Date: Feb 2021 Location: Greenville, SC Posts: 18 Rep Power: 5	Hi Tobias, I tried the old uninstall and install Studio again but the problem persists. I can other entities on the timing map but not the events, even though I can see them in the case setup.

May 12, 2021, 20:10		#4
psrikanth New Member Praveen Srikanth Join Date: May 2021 Location: Convergent Science, Madison, WI Posts: 19 Rep Power: 5	Are these open/close events or valve type events? Another easy way to check if it is an issue with the Studio installation would probably be to open up an example case and see if you can see the cyclic events in the timing map.

May 12, 2021, 23:31		#5
rmotwan New Member Rahul Motwani Join Date: Feb 2021 Location: Greenville, SC Posts: 18 Rep Power: 5	I'm talking specifically about the valve events. Even for the example cases, valve events are not visible, and if I select only Events in Timing Map > Edit, the map is blank.