Only one intersection point was found

amrrhm · May 19, 2016, 21:36

Hi, Does anyone have any idea about this error. What does it mean?

Error: only one intersection point was found.

Converge gives the error at initialization while reading embedded.in.

Thanks

alemoine · May 23, 2016, 10:32

Hi amrrhm,

Have you used the Diagnosis Dock in Converge Studio to verify that there are no intersecting triangles or other major defects in your surface geometry?

Thank you,

amrrhm · May 23, 2016, 18:32

Hi alemoine,

Yes I have checked the diagnostics and there was no major defects in the geometry. I have changed the grid size and the problem was solved!

Thanks

alemoine · May 23, 2016, 18:42

Hi amrrhm,

What version of CONVERGE are you using (including the release date please)? It is interesting that the error message went away after you changed the grid size.

Thank you,

amrrhm · May 23, 2016, 18:47

2.3.8, Also I had my friend run it and he couldn't reproduce the error!

alemoine · May 23, 2016, 18:52

Would you please email your case setup to support@convergecfd.com? We are very interested to hear that this error occurred in v2.3 and we would like to investigate this further.

Thank you,

amrrhm · May 23, 2016, 18:54

I have overwritten that case. If I can find it or reproduce it I will send it to you.

May 19, 2016, 21:36	Only one intersection point was found	#1
amrrhm New Member amrrhm Join Date: May 2016 Posts: 20 Rep Power: 10	Hi, Does anyone have any idea about this error. What does it mean? Error: only one intersection point was found. Converge gives the error at initialization while reading embedded.in. Thanks

May 23, 2016, 10:32		#2
alemoine Member Allie Le Moine Join Date: Jan 2016 Location: Convergent Science, Madison WI Posts: 39 Rep Power: 10	Hi amrrhm, Have you used the Diagnosis Dock in Converge Studio to verify that there are no intersecting triangles or other major defects in your surface geometry? Thank you, __________________ Allie Le Moine Research Engineer \| Applications CONVERGECFD

May 23, 2016, 18:42		#4
alemoine Member Allie Le Moine Join Date: Jan 2016 Location: Convergent Science, Madison WI Posts: 39 Rep Power: 10	Hi amrrhm, What version of CONVERGE are you using (including the release date please)? It is interesting that the error message went away after you changed the grid size. Thank you, __________________ Allie Le Moine Research Engineer \| Applications CONVERGECFD

May 23, 2016, 18:52		#6
alemoine Member Allie Le Moine Join Date: Jan 2016 Location: Convergent Science, Madison WI Posts: 39 Rep Power: 10	Would you please email your case setup to support@convergecfd.com? We are very interested to hear that this error occurred in v2.3 and we would like to investigate this further. Thank you, __________________ Allie Le Moine Research Engineer \| Applications CONVERGECFD

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
problem during mpi in server: expected Scalar, found on line 0 the word 'nan'	muth	OpenFOAM Running, Solving & CFD	3	August 27, 2018 05:18
Running UDF with Supercomputer	roi247	FLUENT	4	October 15, 2015 14:41
block-structured mesh for t-junction	Robert@cfd	ANSYS Meshing & Geometry	20	November 11, 2011 05:59
Regarding FoamX running Kindly help out	hariya03	OpenFOAM Pre-Processing	0	April 18, 2008 05:26
Problem with rhoSimpleFoam	matteo_gautero	OpenFOAM Running, Solving & CFD	0	February 28, 2008 07:51

May 23, 2016, 18:32		#3
amrrhm New Member amrrhm Join Date: May 2016 Posts: 20 Rep Power: 10	Hi alemoine, Yes I have checked the diagnostics and there was no major defects in the geometry. I have changed the grid size and the problem was solved! Thanks

May 23, 2016, 18:47		#5
amrrhm New Member amrrhm Join Date: May 2016 Posts: 20 Rep Power: 10	2.3.8, Also I had my friend run it and he couldn't reproduce the error!

May 23, 2016, 18:54		#7
amrrhm New Member amrrhm Join Date: May 2016 Posts: 20 Rep Power: 10	I have overwritten that case. If I can find it or reproduce it I will send it to you.