Modeling of Solidification using CFX

creddy_trddc · August 26, 2011, 08:27

Hi,

I want to simulate the process involving "Fluid flow+Heat Transfer+Solidification" (Continuous casting).

Can any body please tell me, is it possible to simulate the above process using CFX. I havn't got information on the modeling of solidification using CFX.

Thanks & Regards,
Niranjan Reddy.

Aly · August 26, 2011, 08:32

same problem here

I need to model heat transfer on air flow using cfx

ghorrocks · August 26, 2011, 23:10

People have modelled solidification with CFX but you will need to develop a lot of custom models. Not a task for a CFD beginner. Other simulation codes have solidification models which are easy to use.

Aly: Air heat transfer is easily done in CFX. Unless you are modelling solidification then it is likely your model is easy in CFX.

Aly · August 27, 2011, 06:24

gorrocks please guide me to a good tutorial

All tutorials I found in this part are the same and are not clear !!

ghorrocks · August 27, 2011, 08:10

The tutorials supplied with CFX are quite good. The ones available on the ANSYS community are worth looking at too.

creddy_trddc · August 29, 2011, 01:09

Dear Glenn,

Thanks for your reply...I am looking at other softwares which have solidification module inbuilt

Regards,
Niranjan Reddy.

ghorrocks · August 29, 2011, 19:44

I do not know other codes too well, but I would look at fluent, Flow3D, StarCD. There are also specialist casting and moulding software which would probably have it, such as Thercast (from transvalor), mouldflow and many others.

August 26, 2011, 08:27	Modeling of Solidification using CFX	#1
creddy_trddc New Member creddy Join Date: Aug 2010 Location: Kanpur/UP/India Posts: 25 Rep Power: 16	Hi, I want to simulate the process involving "Fluid flow+Heat Transfer+Solidification" (Continuous casting). Can any body please tell me, is it possible to simulate the above process using CFX. I havn't got information on the modeling of solidification using CFX. Thanks & Regards, Niranjan Reddy.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Modeling plastic injection process in CFX.	psicosis_x	CFX	2	April 13, 2011 15:04
modeling particle transport in ansys cfx 10.0	siavash	CFX	9	November 23, 2010 22:21
PhD using CFX	Rui	CFX	9	May 28, 2007 06:59
Problem in modeling solidification	S. Balasubramanyam	CFX	0	January 20, 2004 10:54
CFX for turbulence modeling	Sujit	CFX	1	August 13, 2003 07:20

August 26, 2011, 08:32		#2
Aly New Member Aly Join Date: Aug 2011 Posts: 10 Rep Power: 15	same problem here I need to model heat transfer on air flow using cfx

August 26, 2011, 23:10		#3
ghorrocks Super Moderator Glenn Horrocks Join Date: Mar 2009 Location: Sydney, Australia Posts: 17,872 Rep Power: 144	People have modelled solidification with CFX but you will need to develop a lot of custom models. Not a task for a CFD beginner. Other simulation codes have solidification models which are easy to use. Aly: Air heat transfer is easily done in CFX. Unless you are modelling solidification then it is likely your model is easy in CFX.

August 27, 2011, 06:24		#4
Aly New Member Aly Join Date: Aug 2011 Posts: 10 Rep Power: 15	gorrocks please guide me to a good tutorial All tutorials I found in this part are the same and are not clear !!

August 27, 2011, 08:10		#5
ghorrocks Super Moderator Glenn Horrocks Join Date: Mar 2009 Location: Sydney, Australia Posts: 17,872 Rep Power: 144	The tutorials supplied with CFX are quite good. The ones available on the ANSYS community are worth looking at too.

August 29, 2011, 01:09		#6
creddy_trddc New Member creddy Join Date: Aug 2010 Location: Kanpur/UP/India Posts: 25 Rep Power: 16	Dear Glenn, Thanks for your reply...I am looking at other softwares which have solidification module inbuilt Regards, Niranjan Reddy.

August 29, 2011, 19:44		#7
ghorrocks Super Moderator Glenn Horrocks Join Date: Mar 2009 Location: Sydney, Australia Posts: 17,872 Rep Power: 144	I do not know other codes too well, but I would look at fluent, Flow3D, StarCD. There are also specialist casting and moulding software which would probably have it, such as Thercast (from transvalor), mouldflow and many others.