FSI error ERROR #001100279(Shell & Tube heat exchanger)

Chandrashekhar · March 26, 2010, 02:46

DEAR all

I have to solve the problem FSI Modelling Shell & Tube Heat Exchanger (Determine Tubes Vibration) using CFX. I have done the meshing of Tubes & baffles in Transient Mechanical part & Meshing of whole domain (shell, tubes ,baffles) in CFX, defined 2 domains (1) shell side fluid with baffles (2) tube side fluid ,mesh motion to be transfered from ansys to CFX. but at the end, when I start CFX solver, I recieve this error message.

Error detected by routine MAKDAT
Error detected by routine MAKDAT
CDANAM = IZN CDTYPE = INTR ISIZE = 1
CDANAM = IZN CDTYPE = INTR ISIZE = 1
CRESLT = OLD
CRESLT = OLD

****** PROBLEM REPORT ******
|--------------------------------------------------------------------
| Subsystem: Input
| Subroutine name: ErrAction
| Severity level: Fatal Error
| Error message number: 001100279
|--------------------------------------------------------------------
| Message:
|
| Stopped in routine MEMERR

can anybody please help me with this error & exactly what BC i should apply for the problem ?

ghorrocks · March 26, 2010, 06:07

Have you run out of memory?

Chandrashekhar · March 26, 2010, 13:26

my laptop's RAM is 4 GB,dual core processor.could it be the problem?

ghorrocks · March 26, 2010, 16:04

Start the job up and watch the task manager. Don't forget if are using a Windows 32 bit OS your limit is 2GB, not 4GB.

March 26, 2010, 02:46	FSI error ERROR #001100279(Shell & Tube heat exchanger)	#1
Chandrashekhar New Member Chandrashekhar Join Date: Mar 2010 Location: Surat,India Posts: 2 Rep Power: 0	DEAR all I have to solve the problem FSI Modelling Shell & Tube Heat Exchanger (Determine Tubes Vibration) using CFX. I have done the meshing of Tubes & baffles in Transient Mechanical part & Meshing of whole domain (shell, tubes ,baffles) in CFX, defined 2 domains (1) shell side fluid with baffles (2) tube side fluid ,mesh motion to be transfered from ansys to CFX. but at the end, when I start CFX solver, I recieve this error message. Error detected by routine MAKDAT Error detected by routine MAKDAT CDANAM = IZN CDTYPE = INTR ISIZE = 1 CDANAM = IZN CDTYPE = INTR ISIZE = 1 CRESLT = OLD CRESLT = OLD **** PROBLEM REPORT **** \|-------------------------------------------------------------------- \| Subsystem: Input \| Subroutine name: ErrAction \| Severity level: Fatal Error \| Error message number: 001100279 \|-------------------------------------------------------------------- \| Message: \| \| Stopped in routine MEMERR can anybody please help me with this error & exactly what BC i should apply for the problem ?

March 26, 2010, 13:26	RAM is 4 GB	#3
Chandrashekhar New Member Chandrashekhar Join Date: Mar 2010 Location: Surat,India Posts: 2 Rep Power: 0	my laptop's RAM is 4 GB,dual core processor.could it be the problem?

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Concentric tube heat exchanger (Air-Water)	Young	CFX	5	October 7, 2008 00:17
Tube in Tube heat exchanger( But I got error)	Young	CFX	2	September 26, 2008 02:35
How to simulate 3D shell and Tube heat Exchanger	san	FLUENT	2	February 22, 2006 06:44
Convective Heat Transfer - Heat Exchanger	Mark	CFX	6	November 15, 2004 16:55
concentric tube heat exchanger	satya	CFX	4	January 16, 2002 10:06

March 26, 2010, 06:07		#2
ghorrocks Super Moderator Glenn Horrocks Join Date: Mar 2009 Location: Sydney, Australia Posts: 17,871 Rep Power: 144	Have you run out of memory?

March 26, 2010, 16:04		#4
ghorrocks Super Moderator Glenn Horrocks Join Date: Mar 2009 Location: Sydney, Australia Posts: 17,871 Rep Power: 144	Start the job up and watch the task manager. Don't forget if are using a Windows 32 bit OS your limit is 2GB, not 4GB.