CFD Online Logo CFD Online URL
www.cfd-online.com
[Sponsors]
Home > Forums > Software User Forums > ANSYS > CFX

confused on messages after solver has terminated

Register Blogs Community New Posts Updated Threads Search

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old   February 21, 2010, 20:29
Default confused on messages after solver has terminated
  #1
Senior Member
 
Join Date: Nov 2009
Posts: 125
Rep Power: 17
mactech001 is on a distinguished road
Dear all,

i'm confused on the messages after solver has terminated.

It does indicate that my simulation has reached the desired residual criteria and has stop the solver as shown below.
================================================== ====================
OUTER LOOP ITERATION = 368 CPU SECONDS = 2.165E+04
----------------------------------------------------------------------
| Equation | Rate | RMS Res | Max Res | Linear Solution |
+----------------------+------+---------+---------+------------------+
| U-Mom | 0.97 | 4.5E-06 | 2.9E-04 | 2.9E-02 OK|
| V-Mom | 0.97 | 2.1E-06 | 1.2E-04 | 3.6E-02 OK|
| W-Mom | 0.96 | 9.8E-06 | 8.4E-04 | 1.8E-02 OK|
| P-Mass | 0.98 | 4.4E-07 | 2.4E-05 | 5.0 9.3E-02 OK|
+----------------------+------+---------+---------+------------------+
| H-Energy | 0.98 | 7.1E-06 | 7.1E-04 | 1.6E-02 OK|
| T-Energy | 0.98 | 4.2E-07 | 7.8E-06 | 5.8 1.6E-02 OK|
+----------------------+------+---------+---------+------------------+
| K-TurbKE | 0.99 | 5.3E-06 | 4.4E-04 | 5.8 2.4E-03 OK|
| E-Diss.K | 0.97 | 1.8E-06 | 1.4E-04 | 12.9 6.9E-06 OK|
+----------------------+------+---------+---------+------------------+

CFD Solver finished: Sun Feb 21 23:08:35 2010
CFD Solver wall clock seconds: 2.1693E+04

Execution terminating:
all residual
are below their target criteria.


BUT then, going further down the message page, it claims there's an error.
+--------------------------------------------------------------------+
| ERROR #001100279 has occurred in subroutine ErrAction. |
| Message: |
| Error disconnecting from shared license socket. |
| |
| |
| |
| |
| |
+--------------------------------------------------------------------+
+--------------------------------------------------------------------+
| Writing crash recovery file |
+--------------------------------------------------------------------+

+--------------------------------------------------------------------+
| ERROR #001100279 has occurred in subroutine ErrAction. |
| Message: |
| Stopped in routine RUNF3D |
| |
| |
| |
| |
| |
+--------------------------------------------------------------------+
+--------------------------------------------------------------------+
| An error has occurred in cfx5solve: |
| |
| The ANSYS CFX solver exited with return code 1. |
+--------------------------------------------------------------------+
End of solution stage.
+--------------------------------------------------------------------+
| The results from this run of the ANSYS CFX Solver have been |
| written to E:\Yi CHENG\cylinder with cooling |
| channel\hseAsm11gridRibsL30H3_001.res

How should i treat this result? is this result acceptable please?
__________________
Thank you for your kind attention.

Kind regards,
mactech001
Currently using: ANSYS v13
mactech001 is offline   Reply With Quote

Old   April 21, 2010, 17:58
Default
  #2
JDA
New Member
 
J. D. Aurand
Join Date: Apr 2010
Posts: 13
Rep Power: 16
JDA is on a distinguished road
Did you have any monitor points? If you did, did they level off with acceptable variances? I don't know a lot about the error messages, but my first thought is that there was a problem with wrapping up the partitioner or returning the license to the pool. If the monitor points are steady, I would take the results as acceptable, but still be somewhat skeptical (i.e. if another run is vastly different, but converges and everything else looks good, go with those results).
JDA is offline   Reply With Quote

Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Working directory via command line Luiz CFX 4 March 6, 2011 21:02
why the solver reject it? Anyone with experience? bearcat CFX 6 April 28, 2008 15:08
Solver Error messages!! Rajit FLUENT 3 August 27, 2006 16:28
compressible two phase flow in CFX4.4 youngan CFX 0 July 2, 2003 00:32
Setting a B.C using UserFortran in 4.3 tokai CFX 10 July 17, 2001 17:25


All times are GMT -4. The time now is 16:17.