CFD Online Logo CFD Online URL
www.cfd-online.com
[Sponsors]
Home > Forums > Software User Forums > ANSYS > CFX

modeling spilling of water from a tank

Register Blogs Community New Posts Updated Threads Search

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old   June 21, 2006, 04:05
Default modeling spilling of water from a tank
  #1
jemteo
Guest
 
Posts: n/a
I'd like model the filling of a rectangular tank and due to a crack, water is expelled from the tank onto the floor.

i can model and simulate water filling the tank, how do i model the expellling of water on the floor and the flow after that?

any advise is very much appreciated
  Reply With Quote

Old   June 21, 2006, 08:31
Default Re: modeling spilling of water from a tank
  #2
Joe
Guest
 
Posts: n/a
i can model and simulate water filling the tank, how do i model the expellling of water on the floor and the flow after that?

In exactly the same way ... just continue your geometry over the tank edge, down the tank exterior wall and onto the surrounding floor...
  Reply With Quote

Old   June 21, 2006, 21:02
Default Re: modeling spilling of water from a tank
  #3
jemteo
Guest
 
Posts: n/a
can i just create my tank mesh and then say mesh that represents an entire room and then use interface in CFX to ensure they are joined?

  Reply With Quote

Old   June 23, 2006, 00:50
Default Re: modeling spilling of water from a tank
  #4
James
Guest
 
Posts: n/a
Hi,jemteo

I am sorry I cann't give you some help.Can you give me some advices on filling tank simulation?

I want to simulate such a tank filling:

the inlet of the vessel is at the bottom,without outlet,and filled with air at 5000Pa.

the liquid flow into it by the pressure of 0.5MPa. How should I set the domain and boundary conditions? Homogeneous Multiphase?

Good luck to you! Regurds,James
  Reply With Quote

Old   June 23, 2006, 01:42
Default Re: modeling spilling of water from a tank
  #5
Rajit
Guest
 
Posts: n/a
Hi James

Use the Volume over fraction model.Initialize the model with 100% air and 0% water.

Regards

Rajit
  Reply With Quote

Old   June 23, 2006, 21:10
Default Re: modeling spilling of water from a tank
  #6
James
Guest
 
Posts: n/a
Hi,Rajit

I did just as you said. But how do I know the filling is good? From the streamline?

By the way,How can I get the Animation of water flow? can you give me some advice in detail ?I know how to use the animate,but cannot solve this situation. Regards,

James
  Reply With Quote

Old   June 25, 2006, 20:33
Default Re: modeling spilling of water from a tank
  #7
Rajit
Guest
 
Posts: n/a
Use the various time steps of the transient simulation to animate the spilling.

Regards

Rajit

  Reply With Quote

Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Filling Tank with Water leff CFX 7 August 21, 2017 08:47
Simple Water Tank Transient 88phil88 CFX 5 March 17, 2014 04:48
Water Evaporation and condensation modeling Linjie FLUENT 3 February 6, 2012 14:08
Modeling of water infiltration into a tank containing a permeable soil idir CFX 8 September 16, 2011 07:40
uptodate water distribution network fredius,magige,tanzanian,(e.a) Main CFD Forum 0 January 27, 2002 08:10


All times are GMT -4. The time now is 00:25.