how to input 2D model into CFX5.7 by using icemcfd

September 23, 2005, 06:43

how to input a 2D model into CFX5.7 by using icem cfd. Please help me.

September 28, 2005, 11:25

Hallo. As I know, use " output to CFX " which is on the toolbar, i.e. last item. Also, you need to mesh your model before output to CFX Prepro.

September 29, 2005, 22:46

Before you do that, you need to extrude 2D mesh in the third direction with one cell. For example, if you 2D mesh is on XY plane, you need to have cell in the Z-direction. CFX can't take a 2D mesh.

September 30, 2005, 05:40

Hallo,

I draw a 3D hollow divergence nozzle with ICEM 4.2. Then I use Tet Mesh to mesh my structure. However, when I tried to write the file to CFX 5, an error messag, " running ICEM CFD/ CAE Interface vers. 4.2.6 "and extra arg: **.msh happened. what did that mean? Is the file after meshing file. msh or file.uns. and when I tried to import mesh from ICEM in CFX pre., it showed that the format is not compatible with CFX. What is wrong? Thank you .

October 1, 2005, 11:54

Even though you output mesh into CFX-5 format in ICEM, you should bring it into CFX-Pre as "ICEM CFD" format. When I use Hexa 5.1 and write file to CFX-5, the default file is called "cfx5" without any extension. The latest release of ICEM will create a gtm file.

September 23, 2005, 06:43	how to input 2D model into CFX5.7 by using icemcfd	#1
yflin Guest Posts: n/a	how to input a 2D model into CFX5.7 by using icem cfd. Please help me.

September 28, 2005, 11:25	Re: how to input 2D model into CFX5.7 by using ice	#2
Ho Guest Posts: n/a	Hallo. As I know, use " output to CFX " which is on the toolbar, i.e. last item. Also, you need to mesh your model before output to CFX Prepro.

September 29, 2005, 22:46	Re: how to input 2D model into CFX5.7 by using ice	#3
longbow Guest Posts: n/a	Before you do that, you need to extrude 2D mesh in the third direction with one cell. For example, if you 2D mesh is on XY plane, you need to have cell in the Z-direction. CFX can't take a 2D mesh.

September 30, 2005, 05:40	Re: how to input 2D model into CFX5.7 by using ice	#4
Ho Guest Posts: n/a	Hallo, I draw a 3D hollow divergence nozzle with ICEM 4.2. Then I use Tet Mesh to mesh my structure. However, when I tried to write the file to CFX 5, an error messag, " running ICEM CFD/ CAE Interface vers. 4.2.6 "and extra arg: **.msh happened. what did that mean? Is the file after meshing file. msh or file.uns. and when I tried to import mesh from ICEM in CFX pre., it showed that the format is not compatible with CFX. What is wrong? Thank you .

October 1, 2005, 11:54	Re: how to input 2D model into CFX5.7 by using ice	#5
longbow Guest Posts: n/a	Even though you output mesh into CFX-5 format in ICEM, you should bring it into CFX-Pre as "ICEM CFD" format. When I use Hexa 5.1 and write file to CFX-5, the default file is called "cfx5" without any extension. The latest release of ICEM will create a gtm file.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
gamma-ReTheta turbulence model for predicting transitional flows	FelixL	OpenFOAM Programming & Development	123	August 30, 2022 12:50
Evaporation model in ansys Fluent 12.1	oldisbest	Fluent UDF and Scheme Programming	12	March 26, 2020 10:11
Water subcooled boiling	Attesz	CFX	7	January 5, 2013 04:32
simulation results for k-w model and SST model	Li	CFX	7	June 29, 2007 05:19
Kato-Launder model	sam	Main CFD Forum	13	September 21, 2006 11:15