Alignment problem in cfx turbo

YOUNS · April 23, 2018, 23:47

Hello

I'm doing analysis for centrifugal compressor.
so Impeller made using bladegen and turbogrid
and Scroll(Volute) made using geometry and mesh.
after there was connected one cfx for analysis and used turbo mode.
Here, however I have a problem.

My warning message is like this.
Cannot create interface between regions Inlet 2(Scroll Inlet) and OUTBlock
OUTFLOW(outlet domain at Impeller, this defined in turbogrid) as they are
not aligned.
This may be caused by an invalid component order. The current
component order is S1, R1, S2, S3.
Please confirm that this is correct before continuing.

I need you guys help.
How to set this to solve this problem.

Have nice day!

Opaque · April 24, 2018, 13:17

There are multiple reasons for this error.

1 - While in CFX-Pre, are the components aligned in a way that the both sides of the interface in question touch each other. If not, use a Mesh Transformation and rotate the component of interest to align as you need.

2 - If the components are aligned properly, are you certain the domain interface is defined correctly? Is the axis of the machine defined correctly? If not the matching algorithm cannot match both sides of the interface.

3 - Is there a large mismatch at the interface so that faces are further apart than you think? Zoom in to see if the faces on both sides touch (within reasonable range), or cross each other (typical of mesh issues)

YOUNS · April 24, 2018, 21:15

Thanks your answer, Opaque

First, It's not problem about physics dimension of geometry.
After hearing your comment, I think that cause of this problem is mesh issues.

For TurboGrid, There is satisfied condition of mesh analysis(all sections) and for volute(scroll), is set below than 0.8 about skewness.

To my think, mesh is fine but, If i have a problem, tell me about that.

Thanks

Have a nice day.

April 23, 2018, 23:47	Alignment problem in cfx turbo	#1
YOUNS New Member seunghyeon, yun Join Date: Apr 2018 Posts: 18 Rep Power: 8	Hello I'm doing analysis for centrifugal compressor. so Impeller made using bladegen and turbogrid and Scroll(Volute) made using geometry and mesh. after there was connected one cfx for analysis and used turbo mode. Here, however I have a problem. My warning message is like this. Cannot create interface between regions Inlet 2(Scroll Inlet) and OUTBlock OUTFLOW(outlet domain at Impeller, this defined in turbogrid) as they are not aligned. This may be caused by an invalid component order. The current component order is S1, R1, S2, S3. Please confirm that this is correct before continuing. I need you guys help. How to set this to solve this problem. Have nice day!

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Mass imbalance problem in multiphase water and steam CFX case	Antech	CFX	1	October 26, 2020 05:03
Convergence problem of CFX when comparing with FLUENT with same mesh	guxin7005	CFX	8	May 22, 2014 16:13
Problem with axial alignment in Turbomachinery	zhaowei	CFX	12	May 4, 2010 06:14
Ansys CFX bucket problem	njsavage	Main CFD Forum	1	April 30, 2009 10:48
CFX 4.4 installation problem	Pandu Sattvika	CFX	1	December 1, 2001 05:07

April 24, 2018, 13:17		#2
Opaque Senior Member Join Date: Jun 2009 Posts: 1,880 Rep Power: 33	There are multiple reasons for this error. 1 - While in CFX-Pre, are the components aligned in a way that the both sides of the interface in question touch each other. If not, use a Mesh Transformation and rotate the component of interest to align as you need. 2 - If the components are aligned properly, are you certain the domain interface is defined correctly? Is the axis of the machine defined correctly? If not the matching algorithm cannot match both sides of the interface. 3 - Is there a large mismatch at the interface so that faces are further apart than you think? Zoom in to see if the faces on both sides touch (within reasonable range), or cross each other (typical of mesh issues)

April 24, 2018, 21:15		#3
YOUNS New Member seunghyeon, yun Join Date: Apr 2018 Posts: 18 Rep Power: 8	Thanks your answer, Opaque First, It's not problem about physics dimension of geometry. After hearing your comment, I think that cause of this problem is mesh issues. For TurboGrid, There is satisfied condition of mesh analysis(all sections) and for volute(scroll), is set below than 0.8 about skewness. To my think, mesh is fine but, If i have a problem, tell me about that. Thanks Have a nice day.