Autodesk Inventor geometry problem

Whitebear · November 23, 2015, 22:35

I use Autodesk inventor as 3D CAD solid model. Autodesk Inventor can export directly *.ipt geoetry file to ANSYS by ANSYS Icon on their menu bar. There is no problem to import geomery and make mesh and setup in ANSYS CFX. But there is an error message " Stopped in routine MEMERR" when I run the CFX solver.

Details of error:-
------------------
Error detected by routine PEEKI
CDANAM=/LPNQ/DB/NREG
CRESLT=NONE

Current Dirrectory: /FLOW/REGMAP

+=========================================+
*****PROBLEM REPORT **********
-----------------------------------------------------------------------------
Subsystem: Input and Output
Subroutine name : ErrAction
Severity level : Fatal Error
Error message number: 001100279
-----------------------------------------------------------------------------
Message:
Stopped in routine MEMERR
+=========================================+

Is there any option that I can solve this problem in Basic Geometry Options or Advanced Geometry Options?

tomson199 · November 24, 2015, 06:27

This problem occured, when you have too large model to your RAM memory. The basis options is following:
-try to increase memory allocated factor in advanced option of CFX solver,
-use more processors to divide your model to smaller parts, it relive your memory RAM

-Maxim- · November 24, 2015, 10:25

when you post more of the error message, we could tell you which memory is not enough e.g. real, integer, etc.
You could just set '2x' in the memory allocation settings for the solver for the respective memory.

Whitebear · November 24, 2015, 19:24

Thank you very much Maxim. I found an error that was caused by language. ANSYS doesn't seem to like non-English one. Other thing was "colour" from Autodesk Inventor. It should be deleted.

November 23, 2015, 22:35	Autodesk Inventor geometry problem	#1
Whitebear Member Jinwhan Ryuk Join Date: Feb 2013 Location: South Korea Posts: 91 Rep Power: 13	I use Autodesk inventor as 3D CAD solid model. Autodesk Inventor can export directly .ipt geoetry file to ANSYS by ANSYS Icon on their menu bar. There is no problem to import geomery and make mesh and setup in ANSYS CFX. But there is an error message " Stopped in routine MEMERR" when I run the CFX solver. Details of error:- ------------------ Error detected by routine PEEKI CDANAM=/LPNQ/DB/NREG CRESLT=NONE Current Dirrectory: /FLOW/REGMAP +=========================================+ **PROBLEM REPORT ******** ----------------------------------------------------------------------------- Subsystem: Input and Output Subroutine name : ErrAction Severity level : Fatal Error Error message number: 001100279 ----------------------------------------------------------------------------- Message: Stopped in routine MEMERR +=========================================+ Is there any option that I can solve this problem in Basic Geometry Options or Advanced Geometry Options? Last edited by Whitebear; November 24, 2015 at 00:10.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[Other] engineFoam new mesh problem	ayhan515	OpenFOAM Meshing & Mesh Conversion	5	August 10, 2015 09:45
UDF compiling problem	Wouter	Fluent UDF and Scheme Programming	6	June 6, 2012 05:43
Gambit - meshing over airfoil wrapping (?) problem	JFDC	FLUENT	1	July 11, 2011 06:59
natural convection problem for a CHT problem	Se-Hee	CFX	2	June 10, 2007 07:29
Adiabatic and Rotating wall (Convection problem)	ParodDav	CFX	5	April 29, 2007 20:13

November 24, 2015, 06:27		#2
tomson199 Member Thomas Join Date: Dec 2014 Location: Poland Posts: 49 Rep Power: 11	This problem occured, when you have too large model to your RAM memory. The basis options is following: -try to increase memory allocated factor in advanced option of CFX solver, -use more processors to divide your model to smaller parts, it relive your memory RAM

November 24, 2015, 10:25		#3
-Maxim- Senior Member Maxim Join Date: Aug 2015 Location: Germany Posts: 413 Rep Power: 13	when you post more of the error message, we could tell you which memory is not enough e.g. real, integer, etc. You could just set '2x' in the memory allocation settings for the solver for the respective memory.

November 24, 2015, 19:24		#4
Whitebear Member Jinwhan Ryuk Join Date: Feb 2013 Location: South Korea Posts: 91 Rep Power: 13	Thank you very much Maxim. I found an error that was caused by language. ANSYS doesn't seem to like non-English one. Other thing was "colour" from Autodesk Inventor. It should be deleted.