|
[Sponsors] |
Maximum words supported by the flow solver exceeded |
|
LinkBack | Thread Tools | Search this Thread | Display Modes |
June 6, 2013, 02:24 |
Maximum words supported by the flow solver exceeded
|
#1 |
New Member
Join Date: May 2011
Posts: 21
Rep Power: 0 |
I am running CFX-Solver on a Windows 64XP OS. The problem is large - 190M mesh elements.
I did a partition run with the large problem partitioner which seems OK. Then with a full run using the partition that part runs OK but I get the following error from the solver when it starts: +--------------------------------------------------------------------+ | Memory Allocated for Run (Actual usage may be less) | +--------------------------------------------------------------------+ Allocated storage in: Mwords Words/Node Words/Elem Mbytes Bytes/Node Partition | Real | Integer | Character | Logical | Double ----------+------------+------------+-----------+----------+---------- 1 | 19479.56 | 1324.77 | 3.92 | 0.12 | 0.91 | 2146.17 | 145.96 | 0.43 | 0.01 | 0.10 | 420.44 | 28.59 | 0.08 | 0.00 | 0.02 | 74308.64 | 5053.60 | 3.74 | 0.11 | 6.93 | 8584.67 | 583.83 | 0.43 | 0.01 | 0.80 ----------+------------+------------+-----------+----------+---------- +--------------------------------------------------------------------+ | ERROR #001100279 has occurred in subroutine ErrAction. | | Message: | | The total number of words needed by the master for the Real stack | | exceeds the maximum supported by the flow solver: 2,147,483,647. | | Please reduce the memory usage. | | | | | | | +--------------------------------------------------------------------+ The thing is I have increased the solver's memory allocation factor to 4 and the master's Real Stack allocations (seen in the table above) change accordingly, but the maximum supported by the flow solver doesn't change at all. If anyone can suggest what this strange flow solver limit, which is below that allocated, is set or caused by it would be much appreciated. Thanks. |
|
June 6, 2013, 07:14 |
|
#2 |
Super Moderator
Glenn Horrocks
Join Date: Mar 2009
Location: Sydney, Australia
Posts: 17,871
Rep Power: 144 |
Have you installed ANSYS CFX for 64 bit or 32 bit?
|
|
June 6, 2013, 07:41 |
|
#3 |
New Member
Join Date: May 2011
Posts: 21
Rep Power: 0 |
Installed ANSYS for 64bit. Thanks for asking.
|
|
June 6, 2013, 07:49 |
|
#4 |
Super Moderator
Glenn Horrocks
Join Date: Mar 2009
Location: Sydney, Australia
Posts: 17,871
Rep Power: 144 |
I suspect what you are seeing is that the partition size you are using is too big for the solver to handle. You are going to have to partition it into smaller partitions.
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Solver for an incompressible, turbulent flow with heat transfer | tH3f0rC3 | OpenFOAM Running, Solving & CFD | 9 | June 17, 2019 07:12 |
thobois class engineTopoChangerMesh error | Peter_600 | OpenFOAM | 4 | August 2, 2014 10:52 |
Suitable solver for Air/Air flow with different temperatures | cjm | OpenFOAM | 1 | January 20, 2011 05:17 |
Inviscid Drag at subsonic, subcritical Mach # | Axel Rohde | Main CFD Forum | 1 | November 19, 2001 13:19 |
fluid flow fundas | ram | Main CFD Forum | 5 | June 17, 2000 22:31 |