cfx remeshing by icem

MUMMED · December 2, 2012, 14:00

hello every body
I'm trying to solve a problem by using icem remeshing.
I followed a post about this in forums but following error has been reported.
I will be grateful for any advice.

raminmir · January 21, 2013, 11:03

in the first photo, the Boundary for Part Map1 is Default Domain Default, does this boundary lay on the ICEM PART NAME "SOLID"? they should be the same.
and pay attention to MONITOR POINT in Scalar parameters.
in the 2nd photo regarding to error, what happens in ccl? remeshing started or you cant get any progress?

MUMMED · February 5, 2013, 06:55

Dear ramin
thanks for your advice
remeshing starts but after that some error appears like fatal error or highly skewness
I checked the remesh which generated after remesh but that was not fine although that was not like previous mesh
I have done edr tutorial about remeshing but this problem occured.
i will be so grateful for your help

raminmir · February 5, 2013, 09:29

I got some problems on mesh not following exactly the geometry, I could not get rid of it totally, but with assigning finger mesh in .rpl file, it got a little bit better.
did you set the mesh motion at top and bot of the box, unespecified or stationary?

MUMMED · February 5, 2013, 10:25

Quote:

Originally Posted by raminmir

I got some problems on mesh not following exactly the geometry, I could not get rid of it totally, but with assigning finger mesh in .rpl file, it got a little bit better.
did you set the mesh motion at top and bot of the box, unespecified or stationary?

I set top and bottom stationary and side walls unspecified
sorry but what do you mean finger mesh?

raminmir · February 5, 2013, 10:54

a mistake; meant "finer"

MUMMED · February 5, 2013, 11:58

Quote:

Originally Posted by raminmir

a mistake; meant "finer"

However thank you for your attention.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Import Mesh from ICEM CFD to CFX	Andre Almeida	CFX	16	April 19, 2016 04:42
CFX and ICEM CFD - structured meshes	realanony87	CFX	10	May 15, 2009 06:17
ICEM for CFX	Al Mazdeh	CFX	7	April 5, 2008 07:32
Ansys CFX 11 FSI and ICEM	Sheeko	CFX	3	November 16, 2006 07:42
Import a rectangular domain into CFX 5.7 from ICEM	SKLam	CFX	9	March 8, 2006 01:47

January 21, 2013, 11:03		#2
raminmir New Member Ramin Mirzazadeh Join Date: Aug 2012 Posts: 16 Rep Power: 14	in the first photo, the Boundary for Part Map1 is Default Domain Default, does this boundary lay on the ICEM PART NAME "SOLID"? they should be the same. and pay attention to MONITOR POINT in Scalar parameters. in the 2nd photo regarding to error, what happens in ccl? remeshing started or you cant get any progress?

February 5, 2013, 09:29		#4
raminmir New Member Ramin Mirzazadeh Join Date: Aug 2012 Posts: 16 Rep Power: 14	I got some problems on mesh not following exactly the geometry, I could not get rid of it totally, but with assigning finger mesh in .rpl file, it got a little bit better. did you set the mesh motion at top and bot of the box, unespecified or stationary?

February 5, 2013, 10:54		#6
raminmir New Member Ramin Mirzazadeh Join Date: Aug 2012 Posts: 16 Rep Power: 14	a mistake; meant "finer"