Ansys Transient thermal message

simox 2 · January 12, 2011, 08:22

What's the meaning of this message?

*** WARNING *** CP = 5.117 TIME= 19:33:29
Element shape checking is currently inactive. Issue SHPP,ON or
SHPP,WARN to reactivate, if desired.

simox 2 · January 12, 2011, 12:25

ok

13 people that visits the message, and another solution?

please help me

sac · January 12, 2011, 13:12

Quote:

Originally Posted by simox 2

ok

13 people that visits the message, and another solution?

please help me

It means the element shape checking is turned off presumably because the job is coming from workbench which does its own shape checking prior to sending it to the solver.

simox 2 · January 12, 2011, 13:16

thank you
this means that there is an error message, how can I possibly turn it on?

sac · January 12, 2011, 18:12

Quote:

Originally Posted by simox 2

thank you
this means that there is an error message, how can I possibly turn it on?

No it is simply warning you that the solver is not doing the shape checking because workbench has done it already.

simox 2 · January 12, 2011, 18:27

perfect, thank you.
I ask you just only the last thing:
when i start the transien thermal analisis the maximum temperature, in the early steps of time, goes above the initial temperature that i have estabilished...it is insignificant!
i think that is possible that i have too penetration between the edges so it's a problem of convergence.
do you know were i can change the penetration parameters of my geometry? only in the original cad file?
I have seen in some forums that there is a command to do it but i don't found it in the ansys mechanical interface!

P.S. i use Ansys Workbench v12

Thank you very much

January 12, 2011, 08:22	Ansys Transient thermal message	#1
simox 2 New Member simone Join Date: Jan 2011 Posts: 5 Rep Power: 15	What's the meaning of this message? * WARNING * CP = 5.117 TIME= 19:33:29 Element shape checking is currently inactive. Issue SHPP,ON or SHPP,WARN to reactivate, if desired.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Transient Thermal Analysis in Ansys Workbench	khurram1	ANSYS	0	November 22, 2010 03:40
single directional message transmit in parallel model	su_junwei	OpenFOAM Programming & Development	1	December 17, 2009 08:00
Transient Thermal Analysis with FSI	Abduri	CFX	2	March 27, 2009 03:47
Transient Thermal Stress Distribution	Ijaz	CFX	0	February 19, 2009 17:27
Error message in CFX-10	CFDworker	CFX	2	October 12, 2007 08:23

January 12, 2011, 12:25		#2
simox 2 New Member simone Join Date: Jan 2011 Posts: 5 Rep Power: 15	ok 13 people that visits the message, and another solution? please help me

January 12, 2011, 13:16		#4
simox 2 New Member simone Join Date: Jan 2011 Posts: 5 Rep Power: 15	thank you this means that there is an error message, how can I possibly turn it on?

January 12, 2011, 18:27		#6
simox 2 New Member simone Join Date: Jan 2011 Posts: 5 Rep Power: 15	perfect, thank you. I ask you just only the last thing: when i start the transien thermal analisis the maximum temperature, in the early steps of time, goes above the initial temperature that i have estabilished...it is insignificant! i think that is possible that i have too penetration between the edges so it's a problem of convergence. do you know were i can change the penetration parameters of my geometry? only in the original cad file? I have seen in some forums that there is a command to do it but i don't found it in the ansys mechanical interface! P.S. i use Ansys Workbench v12 Thank you very much