Pro/e to cfx geometry filler

Jmac · May 31, 2011, 00:23

Hi all,
I am undertaking a cfd analysis of a fairly complex shower mixer component. I have a CAD model of the component itself in pro/engineer but what I require is a model of the internal cavities (where the fluid is flowing through) that can be used for a cfd analysis. Due to the complexity of the part it is not possible to create this from scratch in design modeller or otherwise. Is there a feature on ANSYS or pro/engineer that I can use to create the cfd geometry?
Any help would be appreciated,
thanks

PSYMN · June 6, 2011, 15:41

In ANSYS Meshing, you would want to extract a flow volume... It basically does a boolean subtraction.

In ICEM CFD, you would just place a material point inside and close the inlets and outlets... ICEM CFD is a surface based modeler and doesn't need to do a boolean, you just say which volumes you want meshed...

If you can be more specific about which tool you are using, we can give more specific instructions.

Jmac · June 23, 2011, 20:33

I'm using pro/engineer to transfer to ANSYS CFX

PSYMN · June 24, 2011, 13:03

No, I meant what meshing tool are you using...?

If the answer is ANSYS Meshing, then you could do a flow volume extraction...

May 31, 2011, 00:23	Pro/e to cfx geometry filler	#1
Jmac New Member James McLachlan Join Date: May 2011 Posts: 6 Rep Power: 15	Hi all, I am undertaking a cfd analysis of a fairly complex shower mixer component. I have a CAD model of the component itself in pro/engineer but what I require is a model of the internal cavities (where the fluid is flowing through) that can be used for a cfd analysis. Due to the complexity of the part it is not possible to create this from scratch in design modeller or otherwise. Is there a feature on ANSYS or pro/engineer that I can use to create the cfd geometry? Any help would be appreciated, thanks

June 6, 2011, 15:41		#2
PSYMN Senior Member Simon Pereira Join Date: Mar 2009 Location: Ann Arbor, MI Posts: 2,663 Blog Entries: 1 Rep Power: 47	In ANSYS Meshing, you would want to extract a flow volume... It basically does a boolean subtraction. In ICEM CFD, you would just place a material point inside and close the inlets and outlets... ICEM CFD is a surface based modeler and doesn't need to do a boolean, you just say which volumes you want meshed... If you can be more specific about which tool you are using, we can give more specific instructions. __________________ ----------------------------------------- Please help guide development at ANSYS by filling in these surveys Public ANSYS ICEM CFD Users Survey This second one is more general (Gambit, TGrid and ANSYS Meshing users welcome)... CFD Online Users Survey

June 24, 2011, 13:03		#4
PSYMN Senior Member Simon Pereira Join Date: Mar 2009 Location: Ann Arbor, MI Posts: 2,663 Blog Entries: 1 Rep Power: 47	No, I meant what meshing tool are you using...? If the answer is ANSYS Meshing, then you could do a flow volume extraction... __________________ ----------------------------------------- Please help guide development at ANSYS by filling in these surveys Public ANSYS ICEM CFD Users Survey This second one is more general (Gambit, TGrid and ANSYS Meshing users welcome)... CFD Online Users Survey

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
help simplify geometry for CFX	denjil	ANSYS Meshing & Geometry	0	March 28, 2010 06:27
PhD using CFX	Rui	CFX	9	May 28, 2007 06:59
CFX Post - Inserting additional geometry	Andrew	CFX	2	April 18, 2007 09:27
Geometry and meshing with CFX	Bob Crad	CFX	3	January 7, 2004 13:56
CFX 4.4 installation problem	Pandu Sattvika	CFX	1	December 1, 2001 05:07

June 23, 2011, 20:33		#3
Jmac New Member James McLachlan Join Date: May 2011 Posts: 6 Rep Power: 15	I'm using pro/engineer to transfer to ANSYS CFX